Scholars Central

Conference abstractPublished 22 Jun 2020

Pore size enhancement in TiO2 thin films and its effects on dye sensitized solar cells

Authors: Dinfa L. Domtau

University of Jos, Nigeria

Ask about this article

Abstract

Select any words in the title or abstract, or press this and choose a sentence.

Light harvesting efficiency in dye sensitized solar cell is currently enhanced by the employment of an additional TiO2 scattering layer hence increasing the overall film thickness. This has limitations on effective charge transport especially in dense electrolyte media due to the increased film thickness. The additional film layer further reduces light intensity on the adsorbed dye hence decreasing photocurrent generation. Therefore, there is still the challenge of light scattering optimization versus charge transport and photocurrent generation. In addition, though TiO2 is a relatively cheap material, the addition of TiO2 layer raises the production cost of the dye sensitized solar cell effectively and rendering it not cost effective. In this study, carbon black was employed to create artificial pores in TiO2 thin films to enhance light harvesting and hence photocurrent generation. TiO2 films deposited by screen printing method had 0, 1.0, 1.5, 2.0 and 3.0 wt% carbon black. On annealing of the films at 500oC in air for 30 minutes, carbon black decomposed leaving behind voids. Transmittance, reflectance and absorbance spectra of the films determined by a UV-Vis-NIR show that transmittance decreased as the carbon black concentration increased. On the other hand, both reflectance and absorbance increased with increase in carbon black concentration. Micrograph images obtained from both Scanning Electron Microscope (SEM) and Atomic Force Microscope (AFM) show that the pore size of the films increased as the carbon black concentration increased. Furthermore, the XRD results of these films show that the TiO2 are anatase and without any carbon contamination. Conductivity of the films determined using a four point probe was found to decrease with increase in pore size due to decrease in electrical contacts among the TiO2 molecules. The values 384.61, 352.11, 103.41, 52.41 and 35.29 Siemen’s cm-1 were determined for 0, 1.0, 1.5, 2.0 and 3.0, respectively. Current-Voltage (I-V) characteristics of the cell fabricated with different pore sizes were determined using a solar cell simulator at 100 mW/cm2 illumination. The results show that photocurrent generated by these cells increased from 6.1 mA/cm2 to a maximum value of 9.9 mA/cm2 as the wt % carbon black increased from 0 wt% to 1.5 wt %, respectively. Beyond 1.5 wt%, photocurrent begun to drop until it got to its minimum value of 4.7 mA/cm2 at 3.0 wt%. The overall efficiencies for 0, 1.0, 1.5, 2.0 and 3.0 wt% were found to be 2.3, 2.6, 4.3, 2.4 and 1.4 %, respectively. The result shows an improvement in the photovoltaic performance of DSSC as a result of the artificial voids created. However, beyond the optimum concentration of 1.5 wt%, the cell performance begun to decline. This approach greatly enhanced the current density of the cells and consequently the overall conversion efficiency significantly.

Ask about this article

Answers come only from this article's title, abstract and keywords, each sentence pointing to where it comes from. Your question is sent to OpenAI to write the answer. Scholars Central does not store it.

Try:

Follow

New articles from what you follow go into your email digest, once you agree to alert emails.

  • SubjectEnergy & Power
  • SubjectMaterials Science
  • BylineArticles whose byline prints “Dinfa L. Domtau”

For authors and organisers

Publish, present and keep up with your field

Find the right journal for your paper and submit your manuscript.

Photo: Pexels