Research article · 2016
Conference abstract
Comparison study between light-emitting diode and quartz tungsten halogen light curing systems
Abstract
Select any words in the title or abstract, or press this and choose a sentence.
Objective: The purpose of this study was to measure the temperature rise caused by 10 light-emitting diodes (LED) and three quartztungsten- halogen (QTH) dental curing lights and to relate the measured temperature rise to the power density of the curing light. The hypothesis was that the temperature rise induced by the LED curing lights would be smaller than that generated by the QTH curing lights operating at the same power density. Materials & Methods: The curing lights evaluated in this study included a conventional QTH light (XL3000, 3M ESPE, St. Paul, MN, USA), two high-intensity QTH lights (Optilux 501, SDS/Kerr, Orange, CA, USA; Elipar Highlight, 3M ESPE) and 10 LED curing lights (Aqua Blue, Toesco, Kanagawa, Japan; CoolBlu, DentalSystems, Tokyo, Japan; DioPower, CMS, Copenhagen, Denmark; Elipar Freelight, 3M ESPE; Elipar Freelight 2, 3M ESPE; L.E. Demetron 1, SDS/Kerr; Lux-OMax, Akeda, Lystrup, Denmark; Lux-O-Max P1, Akeda; SmartLite, Dentsply, Konstanz, Germany; Ultra-Lume 2, Ultradent Products, South Jordan, UT, USA). The estimated relative heat generated by the curing lights was determined by measuring the temperature rise on the surface of a 4Ã?4 mm cylinder of resin composite (Tetric Ceram; Ivoclar Vivadent, Schaan, Liechtenstein) using a thermocouple connected to a galvanometer (Radiometer, Copenhagen, Denmark). All measurements were made at the end of a 20-second exposure to the curing light. Power density was measured using a dental radiometer (Demetron Research, Danbury, CT, USA). The data were evaluated statistically by regression analysis and by the Newman-Keuls multiple comparison test. Results: Taking all curing lights into consideration, the coefficient of correlation between temperature rise and power density was very good and statistically significant at r=0.93 (p<0.001). The correlation coefficient for only the LED curing lights was even stronger, r=0.96 (p<0.001). This means, of course, that temperature rise increases with increased power density. On the plotted LED regression line, the temperature rise of two of the three QTH curing lights exceeded (by 2 and 2.3 °C) the projected temperature rise of an LED curing light measured at the same power density (650 mW/cm2). The measured temperature rise of the conventional QTH curing light operating at 360 mW/cm2 was not significantly different from the predicted LED temperature rise regression line. Conclusion: In general, the hypothesis that temperature rise caused by LED curing lights would be less than that generated by QTH curing lights operating at the same power density could not be confirmed. The data did not support earlier findings that LED curing units generated smaller temperature rises than QTH curing lights. The authors concluded that the main reason for earlier findings was that first-generation LED curing lights had lower power densities than present-day lights.
Keywords
Subjects
Dentistry & Oral HealthAsk about this article
Answers come only from this article's title, abstract and keywords, each sentence pointing to where it comes from. Your question is sent to OpenAI to write the answer. Scholars Central does not store it.
Similar by topic
Conference abstract
Morphological changes in oral mucosa of rabbits induced by light emitting diode (LED) used as dental curing light
Conference abstract · 28 Nov 2016
Comparison of the Alendronate and irradiation with a light-emitting diode (LED) on murine osteoclastogenesis
Research article · 2018
Comparison of GeneXpert against Light-Emitting Diode Fluorescent Microscopy for the Diagnosis of Pulmonary Tuberculosis in Addis Ababa, Ethiopia
Article · 21 Mar 2023
Comparison of Bonding Technique with Two Different Light Cure Systems and Effect of Two Different Bonding Primers on the Shear Bond Strength Of Orthodontic Brackets: An In Vitro Study
More from this journal
The newest in Dentistry.
Article · 30 Mar 2026
Dental Biomaterials in Contemporary Oral Rehabilitation and Tissue Compatibility
Article · 30 Mar 2026
Oral Microbiome Dynamics in Human Dental and Periodontal Environments
Article · 30 Mar 2026
Digital Dentistry Workflows in Modern Clinical Practice
Conferences in this field
Upcoming conferences in this field.
Follow
New articles from what you follow go into your email digest, once you agree to alert emails.
- JournalDentistry
- SubjectDentistry & Oral Health
- BylineArticles whose byline prints “Ahmed Elmarakby”

