stacked on top of each other to significantly increase altitude. The high compressive strength of the solidified polyurethane foam is sufficient for temporary support structures, or structural reinforcement allowing
replacements of ordinary Portland cement with carbonated solid wastes were tested for compressive strength development and autoclave soundness. The mortars were casted into 50 mm × 50 mm × 50 mm molds
some degree of molecular interaction. The mechanical properties such as Vickers hardness, flexural and compressive strength were enhanced achieving better than the level of ISO standard and the surface roughness
observed that use of reactive phosphorous based flame-retardant in polyurethane foams showed improved compressive strength without affecting closed cell content and morphology of the foams. The horizontal burning test
objectives and this study will be mainly concentrated on experimental works. Experiments regarding compression strength and spilt tensile strength on the partial replacement of egg shell powder and egg yolk…
causes from the destruction of structures and cracks, to the reduction of tensile and compressive strengths. These pathologies affect the durability and safety of concrete structures, which are enhanced
process change and 87% after the process change, respectively. Mechanical properties such as compressive strength and bending strength were evaluated as excellent for the sample after the process modification. Optimized
analyzer (XRD) is used for micro structural characterization. The properties like ultimate tensile strength, compressive strength and micro hardness were investigated. The results of micro hardness revealed higher…
experimental investigations were carried out. Mechanical properties of the material such as tensile strength, compression strength, flexure strength and impact strength were obtained from the experimental investigation…
subjected to characterization and evaluation by advanced technique. Mechanical potential such as tensile strength, compressive strength, wear resistance, modulus of elasticity, modulus of rupture, stress at the limit of…
soils, have good plastic properties so that increased moisture results in their decreased shear strength, compressive strength and volume changes. These damages typically take an irreparable toll on structures, which
composites decreased significantly by inclusion of these fillers. The flexural properties, interlaminar shear strength, compressive strength, density and hardness were also affected by the type of content of filler…
using focused ion beam microscopy for high position site accuracy. Mechanical testing included flexural strength, compressive strength, Young´s modulus and fracture toughness. The nanostructures contribute to high…
pack was formed in fluid channels by gel particles and its compressibility depends on PPG particle size, gel strength, types, brine concentration and load pressure. Gel pack is compressed ... increases. A weak PPG with…
Kenaf fiber in different proportions. In this study the mechanical properties where obtained in compressive strength and tensile strength. The test where conducted using different combination of fibers with volumetric…
ceramic properties evaluated were water absorption, apparent porosity, apparent specific mass, flexural strength and compressive strength. The results indicated that the incorporation of 5% of blast furnace sludge
antioxidant-chitosan-nano-diamond were also evaluated. Mechanical performance such as tensile strength and compressive strength were measured as well bio-adhesive studies were investigated in order to assess
pore interconnectivity and a permeability value of 16.8 x10-10m2. The average compressive strengths and compressive moduli of the natural polymer foam and marine sponge replicas were
percentages recycled waste plastic (polyethylene). Almost 126 samples of concrete are prepared, the concrete Strength (compressive, splitting tensile and flexural strength) are investigated along a time interval…
casting technique. The volume fraction of ANP varied between 0.5 and 1.5 vol%. The compressive deformation behaviour of these composites was investigated as a function of ANP content at different ... Strong bonding…
Soft clay soils, characterized by their low shear strength and high compressibility, pose significant challenges in construction and civil engineering. Traditional stabilization methods often involve high costs and…
silica fume using super plasticizer is investigated. Properties of hardened concrete like ultimate compressive strength and split tensile strength have been determined for different mix combinations of materials and…
tested at the University of the Philippines College of Engineering Mechanical Laboratory for compressive and tensile strength. Acceptance or rejection of the null hypothesis was conducted using the t-test ... level of…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.