length and a pre-loaded collagen cartridge that contains 5 grams of powder. A maximum of 2 grams is applied depending on the area to be covered. Results: Eighteen consecutive
treatment of boils, wound ulcers and convulsion. C. bicolor leaves were collected, dried and powdered. Extraction was done by maceration in methanol to yield the Whole Extract (WE). Successive extraction
this work, we hydrolyzed cellulose pulp using a sulphuric acid method [5] to a powder form and prepared mixtures of this material with low-density polyethylene (LDPE) in order
different times (2,4,6,8)hours. The pack powder mixture consists of 18Al-8Si-2NH4 Cl-72Al2 O3 (wt.%) for silicon modified aluminide diffusion coating and replaced 1% from
safe hypoglycemic agent. Its fruit is olive green in colour. From powdered crude drug using methanol as solvent, separating active material is extraction. Soxhlet assembly is used for extracting
Concrete (UHPC) is a steel fibre reinforced concrete consisting of optimal gradation of fine powders and a very low amount of water cement ratio. This paper describes the possibility
oxidation (%) and μmol Trolox Equivalent/g (μmol TE/g) respectively. For antibacterial test, the powdered dried leaves were extracted using absolute methanol. The disc diffusion method was used to screen
Ketoprofen nanoparticle showed a reduction in an average particle size compared to pure powder and DSC DSC illustrated that the crystallinity of Ketoprofen was partially lost in lyophilized powder
flavonoids, reaching 2.56% and 2.03% respectively. Moreover, the content of pectin in the dry powder of KLB was the highest (21.71%). The highest content of pectin
Diffraction (XRD) analysis. The efficiency of mesoporous silica filters, obtained by powders pressing, to retain heavy metals, was tested on water samples enriched with different amounts
mechanical properties and microstructure of cement based materials. For this purpose nano-SiO2 powders were obtained by sol-gel method using different molar ratios of TEOS/ethanol/water. The formation
more corrugated with the concentration of gallium hydroxide during the dry of GO powder. The graphene oxide structure was distorted due to the three hydroxyl groups of gallium hydroxide
developed by electrospun PVDF nanofibrous membranes incorporated with various weight fractions of WO2.72 powders. The effects of WO2.72 and electro-spinning (ES) parameters on the crystal structure and pyroelectric…
TbF3 which was well attached to the surface of the magnet. Good adhesion of powder is one of the main quality parameters for the successful grain-boundary diffusion process. Compared ... simple dip-coating, EPD gives…
root in both normal and Streptozotocin induced diabetic mice. The diverse features of the powdered root were observed macroscopically using the standard description of terms. The powder is light brown
recovery of photocatalyst. In this work, we synthesized bare and Cu doped TiO2 powder samples, which were characterized by X ray diffraction, micro-Raman spectroscopy, optical spectroscopy in ultraviolet
ions were substituted in Ã?²-TCP. The Si- and Fe- substituted Ã?²-TCP powder were synthesized by co-precipitation method. Crystal structure and thermal properties of Si- and Fe-substituted
Village, Konduga, Borno State in February, 2016. The air-dried extracts were ground into powdered form using mortar and pestle, extracted separately with ethanol (70%) by reflux technique
sintered valve seat insert (VSI) after heat treatment. Such VSI was obtained by powder metallurgy technique and fulfilled the requirement to replace cobalt and lead, used in the original alloy ... respectively. The…
Experimental Detail: TCF preparation involved drying at 100⁰C for 12 hours. The obtained powder was then sieved to 149 microns and was characterized using a scanning electron microscope
graphene oxide (GO) was prepared by variations of the Tour using natural graphite powder as starting material. The GO was synthesis procedure is described as follows: for oxidation stage ... boric acid (H2SO4/H3BO3…
experiment work shows the results of microstructure evolution of the W20Cu alloy obtained by powder metallurgy method, where it was possible to obtain the crystallographic parameters and confirmation
spectroscopy. As a result, the optimal iron to cobalt doping ratio in bismuth titanate powder resulted in ~1.94eV decrease in the optical band gap. In the film form
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.