pyroelectric technique is that it allows studying a large variety of materials including rough surfaces. Mechanistic studies of the formation of mixed crystals by intentional doping or by occluded impurities
gypsum, and water from the gypsum seeping into the acrylic resin. Also, the relatively rough surface of gypsum mould may be penetrated by acrylic denture base resin and adhere
with previous studies. Incorporation of CX into DMPC bilayer resulted in increase of the surface roughness (RRMS= 0.39 nm) and in increase of thickness in average
material is a spheroidal graphite cast iron. 2D and 3D micrographs, 2D and 3D surface roughness parameters were presented. Graphene coating showed slightly lower friction value between ball and coated
three-dimensional topographic technique with a high atomic resolution to measure surface roughness. AFM is a kind of scanning probe microscope (SPM) and it’s a near field technique which ... based on the interaction…
37oC for 24 hours in distilled-water. SBS was measured for each group. Surface roughness of resin composites profiled. Findings: Using coarse diamond in isolation resulted in statistically significantly lower…
study. Another thirty six disc-shaped specimens with the same dimensions were prepared for surface roughness (Ra) determination using a non-contact 3D-optical-profilometer. Baseline and after immersion ... sport energy…
treat surfaces at high temperatures, was found to increase compressive residual stress and decrease surface roughness compared to WJC and SFN-WJC, which had low luminosity and are forms ... higher cavitation…
rate. In this study, we aimed to modify the PTFE surface without increasing the surface roughness using atmospheric pressure plasma to improve the adhesion property to Ag ink film ... PTFE adhesion strength was 0.06…
laser surface engineered polyethylene terephthalate films. Changes in surface characteristics were evaluated through surface roughness and XPS. Morphological changes were observed by SEM and Light microscopes…
Chitosan concentration and curing time was evaluated with respect to entrapment efficiency, particle size, surface characteristics and In-vitro release behaviors. Infrared spectroscopic study confirmed the absence of…
rate. In this study, we aimed to modify the PTFE surface without increasing the surface roughness using atmospheric pressure plasma to improve the adhesion property to a Ag ink film ... PTFE adhesion strength was 0.06…
maltodextrin presented a final product with higher RPC. Based on the analysis of response surface graphs, an assay was selected and physically characterized: apparent density ... particles showed uniform size and formed…
cartilage was quantitatively described using collagen fibril D-periodic spacing, fibril diameter, and surface roughness. Cartilage collagen fiber distribution was inhomogeneous in dehydrated condition but more…
vitro biocompatibility. After sintering the scaffolds show high porosity (about 70 %) and high surface roughness (Ra about 25 μm, Rz up to 200 μm) which is beneficial for the colonization ... stem cells showed an…
droplets can be controlled the transport in directions by designing the temperature, photo, rough-responded surfaces on fibers; the continuous size spindle-knots fiber can realize the droplet transport
room temperature by Ion beam assisted Molecular Beam Epitaxy deposition. Crystal linty, Microstructure, Surface Roughness, electrical and optical prosperities of thin films were investigated as function of deposition…
height were about 100 μm and 8 μm was fabricated and the surface roughness of the micro-channel with the 100×320 μm2 area was about 179 nm measured ... width of micro-channel in the Bio-PDMS microfluidic device was…
dimples over the surface enhances the intricacy level of airflow. These small dimples provide surface roughness and drag reduction as compared to a smooth sphere of same size. Varying geometry ... golf ball by dropping…
structure with more compact, homogeneous and fine microstructure. Furthermore, with increased surface hardness, roughness reduction, corrosion rates was approximately 10 times smaller when compared with the untreated…
increase in the Raman bands with the time of electroplating up to a surface roughness of mean value ~1.35 nm (measured by scanning tunneling microscopy (STM)). This was followed ... cresyl violet (CV). These results are…
27nm by increasing Ce concentration, atomic force microscopy (AFM) analysis shows that th e surface roughness of the samples increased from 1.14 for pure ... wrinkled shape with different size depending upon the Ce…
years. The aim of this review article was to present data about the wear, surface roughness, fracture strength, optical properties, and marginal fit of monolithic zirconia. A PubMed search ... full-coverage”. Based on…
measurements of these nanostructured coatings, Fig. 1, have also demonstrated that the surface roughness of high aspect ratio is one of the most important parameters to be optimized to achieve ... Montero et al. (2014)…
Lange R, Becker P, Rychly J, Beck U, et al. (2005) The influence of surface roughness of titanium on Ã?²1- and Ã?²3-integrin adhesion and the organization
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.