Influence of additives on the properties of ceramics from electrofusion corundum
calcining at 1450Ã?ºC.The porosity after firing was 60-65% and the compressive strength
Articles, journals and conferences in one search. An exact title, DOI or ISSN is listed first.
In the search box: "exact phrase" · -leave out · OR · prefix* · title: author: journal:
calcining at 1450Ã?ºC.The porosity after firing was 60-65% and the compressive strength
alone was also used. Foundry properties like permeability, scatter index; mouldability index, moisture content, compressive strength tests and refractoriness were examined. The results revealed that the binder
structural and mechanical properties of the hydrogels were evaluated by SEM, FTIR and compressive strength test, respectively. Also, the equilibrium swelling ratio of each hydrogel and their degradation rate
distribution of β-TCP nanoparticles in Gelatin- Chitosan (GC) matrix. GCT scaffold showed higher compressive strength of 2.45 ± 0.15 MPa as compared to 1 MPa exhibited by neat GC scaffold
elastic and inelastic property. Measurements based on experiments were first done. Mean values of compressive strength and modulus of elasticity were obtained for several samples. A three-point bending test
exists in resulting samples. Performance to stress increased with pH and maximum compressive strength was found at pH 10. Calcination was found maximum 3.485 Nmm-2 at 900°C minimum
contribution describes testing of compression strength, flexural strength, abrasion resistance, erosion resistance, capillary water absorption and impact resistance of earth briks, called adobe, made up of soil, was…
with the addition of 10 wt% TiO2; however, the ultimate compressive strength decreased from ~237 to ~184 MPa. During sintering process, synthesis of the MgTiO3 nanoflakes via the mechanically induced
hazardous waste using thermal plasma technology. The geopolymers produced from this material can achieve compressive strengths of over 70 MPa displaying properties which are competitive to commercially available cements
humid H2S gas and H2S rich brine were investigated using designed unidirectional samples. Compressive strength, microhardness, porosity, gas permeability, SEM, EDS, and XRD analyses were conducted to compare the…
humid H2S gas and H2S rich brine were investigated using designed unidirectional samples. Compressive strength, microhardness, porosity, gas permeability, SEM, EDS, and XRD analyses were conducted to compare the…
sodium hydroxide solution were used as alkali activators in different mix proportions. The actual compressive strength of the concrete depends on various parameters such as the ratio of the activator
sodium Hydroxide solution were used as alkali activators in different mix proportions. The actual compressive strength of the concrete depends on various parameters such as the ratio of the activator
physical properties of the composites were studied. Mechanical tests showed that flexural and compression strength of the composites markedly increased with the modifier content, reaching 4.712 and 9.75 MPa when
coarse brick aggregate content. Concrete samples made with brick aggregates showed slight improvement in compressive strength compared to that in concrete made with 100% natural aggregate. By increasing the brick
concomitant injections for engineering studies include hydrological and geological and that injections accompanied by compressions strength large create new depression may contribute to the ancient after cracks found
humid H2S gas and H2S-rich brine were investigated using designed unidirectional samples. Compressive strength, microhardness, porosity, gas permeability, SEM, EDS, and XRD analyses were conducted to compare the…
mode was rather a premature local buckling mode. I-shaped steel stubs had higher compression strength a lower load decrease rate compared to rectangular steel stubs. Providing rectangular steel stubs
standard concrete with no replacement. Mechanical properties that have been of keen interest are compressive strength, flexural strength and modulus of elasticity and durability tests comprised of depth of carbonation
standard cylindrical specimens and model core-drilled specimens were made to determine the compressive strength of concrete and to check for non-uniformity, segregation and bleeding in the processes
heavy metal composition, calorific value, bulk density, moisture content and Chlorine and Alkali contents. Compressive strength, particle size of component materials as well as combustion and ignition temperatures was…
improve the workability of concrete. The mechanical properties were assessed from the compressive strength, tensile strength and flexure. While the durability characteristics were investigated in terms of alkalinity and…
addition for mortars and concretes, in the presence of a superplasticizing admixture provided maximum compressive strength at the same workability level, comparable to that of the reference mixture after
respectively. Steel fibre lightweight concrete has a compressive strength, fcu of 14.29N/mm2. The ultimate carrying strength of the wall panel ranges from 100kN to 138kN and the highest
specimens were cured for 7 & 28days before compression strength test etc. Results that workability increases with increase in percentage of FS and feasibility study on the use of broken Mangalore
For authors and organisers
Find the right journal for your paper and submit your manuscript.