different seat configurations and loading conditions. The results showed that the seat suspension was nonlinear, with the transmissibility dependent on the magnitude of excitation and distribution of the vibration energy
drug-loaded NP preparations, which were ~170 nm in size and had drug loading values of ~2%, were shown to reduce cell viability and cell compartment-specific, as well ... drug in two GBM cell lines. Following…
properties. PEG coated NPs (PCN) loaded with Dapivirine was characterized for particle size distribution, morphology, loading efficiency and mucus infiltration properties. The cellular uptake profiles of PCN by human…
grid at various times of the day. While they may be considered as a load, their batteries may be exploited as battery energy storage system (BESS) devices thereby becoming ... balancing the demand and supply of…
increased energy losses that appear after integration of single phase electric vehicle charging load in a distribution network and the obtained results may serve as a guiding parameters for network
intelligent energy storage solutions are employed to mitigate their corresponding disturbances to the energy distribution infrastructure. These energy storage solutions are augmented with grid information for its…
connectivity. This approach will use a model consisting smart metering and flexibility for supply, load and tariff management, where energy credits will be provided to the users on prepaid basis ... fees. Existing…
benefits of ultra-high performance concrete (UHPC) on a ductility, energy absorption, crack distribution, damage tolerance, and deformation capacity. Nevertheless, little information is available on the behavior of UHPC…
were measured at a crosshead speed of 1 mm/min and a 50-kg load cell. Significance for all statistical tests was pre-determined at p<.05. Results: In-vitro ... with time from 12 hours to 7 days in both the units. An…
pedobarographic findings we observed while the subjects were standing revealed no difference of force distribution and contact area between forefoot and rearfoot and this finding did not support the hypothesis ... body…
replacement of the first molar with the prosthesis. The load applied to bridges was defined as concentrated and distributed. The implant is installed on the site of the first premolar
assessing the poroelastic response of materials to prolonged loading by estimating and mapping the time-dependent distribution of the local axial strain and lateral-to-axial strain ratio, often referred
case of non-linear loads in grid connected systems. In this paper, we introduced a new series-shunt type FACTS controller called as distributed power flow controller. This DPFC method
upgraded properties and improved performance. Certain design properties such as quality, cost reduction, uniform distribution, mechanical properties, and tribological properties of the composites depends on fabricating…
connection of non-linear loads and this issue has to be suppressed. This paper assesses the impact of PV generation on the distribution system and important issues such as reverse
ignition engine, particularly targeting on soot formation in terms of mass and particle size distribution. The corresponding computational fluid dynamic modeling was performed by KIVA4 coupled with CHEMKIN II code…
guidelines for the geometry and dimension parameters of this CVT layout for uniform axial loading and optimal ratio range. First a kinematic analysis is done in order to find ... lubrication theory (in case of journal…
efficiency of the hybrid vehicle is use of auxiliary power sources for temporary loads inside and outside the vehicles. This allows the main energy source(s) to be used only ... drive the vehicle and therefore increase…
scene using IBR representation requires many images. it's impossible for mobile devices to load the whole data set into their memories. Fortunately, small parts of the entire data ... thanks to the expensive compression…
crown-to-implant (C/I) ratio on the stress distributions in bone and implant under axial and oblique loads by using three-dimensional (3-D) finite element analysis (FEA) method ... value in implant was 312.7 MPa under…
develop O/W nanoemulsion system of riluzole to improve its brain bioavailability. Methods: Riluzole loaded nanoemulsion was prepared by phase titration method. It was consisting of 3% w/w Sefsol ... water. It was…
mortality particularly among children (1:5 children of hospital admission either partially/completely) as distribution of genetic diseases is not related to socioeconomic background, which implies that developing world…
While best management practices (BMP) are recommended to attain non-point source loads in receiving water bodies, it is still unclear whether their efficiency will be maintained under future climate ... semi-distributed…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.