conditions of the motor hardware, it will be subjected to high temperatures and pressure loads. Structural and thermal design has to carried out for a given input parameters and analysis
irregularity of the life style, which, through night duties and unexpected further work-loads or cancellations of off-duty-times; keeps damaging the husband-role. In American Police Force, especially
This paper describes the approach for establishing the Design Accidental Load (DAL) fire based on a grid-based fire risk analysis. Representative cases are screened via an initial fire risk
this study the influence of corrosion and seismic load (low-cycle fatigue LCF) in the mechanical performance of reinforcing steel bars of S400 grade with 10 mm nominal diameter
positions of a functionally graded piezoelectric material (FGPM) strip is analyzed under transient thermal loading conditions. It is assumed that the thermoelectroelastic properties of the strip vary continuously along
with an angular speed. Results comprising of Minimum lubricant film thickness, Dynamic pressure and load, Wall shear stress, Eccentricity, Temperature distribution and heat flux with respect to time are presented
targeted to analyze the development in existing scissor car jack in order to make load lifting easier by utilizing Car battery (12V) which can be used in emergency situations
Offshore structures such as boats, ships, oil rigs etc. are under continuous wave loading. These waves exert pressure on the structure which in turn produces stresses in them. These waves
higher than those from spark ignition (SI) engines, especially at low engine load when the EGR rate or the residual gas required to control NOx emission are elevated. Toxic chemicals ... catalyst performance will be…
used to conduct the dry sliding wear tests. The experiments were conducted by varying loads and sliding speeds for sliding distance of 2000 m. The results revealed that Al6061 ... composites. Further, the volumetric…
results and published experimental results. In macro level study of laminates first ply failure load of laminates is calculated using ANSYS and compared with analytical results. Various failure theories ... theory…
some of Ca2+ ions by some other ions of group 2 modifies biological and load bearing properties. Many methods are available for synthesizing these doped HAp samples characterized by particle
concentration of sodium alginate along with commercial diet was tested. The total heterotrophic bacterial load ranged from 4.4 × 102 CFU/g to 11.2×102CFU/g of gut sample. The maximum
pollution level along the river Ghaghara is not very high but the increasing population load in the basin may cause irreparable ecological harm in the long-term well masked
Factor analysis of the data showed emergence of two factors. Most items loaded significantly on head and body factors. The internal consistency using frequency was 0.96 and using intensity
measured by a dialysis method. The entrapment efficiency of curcumin was 94.7% and the loading capacity was 3.06% under optimized conditions (curcumin 5 mg, Pluronic P123 150 mg, water
This study deals with the determining of coliform counts through MPN test, total heterotrophic load of bacteria, isolation and identification of the Bacteria through plating on different selective medium ... shows that…
cycles. Both natural and anthropogenic sources were found to be contributing to the pollution load of the rivers in Maharashtra with the anthropogenic activities dominating the influence. Chemical weathering
obtain adsorption kinetics of Co2+ ions onto granular activated carbon F-400 loaded with Salicylic acid, 3,5-Dinitrosalicylic acid and 5-Sulphosalicylic acid one by one at constant temperature
devoid of solvent usage. The incorporation of solid dispersion at 20% drug load into a tablet resulted in a rapid release tablet dosage form with enhanced dissolution properties
drug delivery system. Sucralfate acts as the cytoproytective agent and carry the antineoplastic drug loaded nanoparticles to the carcinoma site in the g .i.t which will protect and alleviate
hottest-spot winding temperature is the principal factor in determining life due to loading. The temperature cannot be measured directly because of the hazards in placing a temperature detector ... forecast the nature…
eight trial beams. Four beams were fabricated and experimented under two point loading. A tension test was done for three series of specimens with 2 mm thickness to determine ... Young’s modulus and yield stress. It was…
chloroform fraction (AA-CC4) in qualitative DPPH assay showed activity at a loading dose of 0.05 µg, thus exhibiting radical scavenging activity comparable to that of ascorbic acid
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.