Reactive Power Compensation of Hybrid System Having Induction Motor Load
mathematical modelling of the system. The MATLAB/SIMULINK environment is used for simulation
Articles, journals and conferences in one search. An exact title, DOI or ISSN is listed first.
In the search box: "exact phrase" · -leave out · OR · prefix* · title: author: journal:
mathematical modelling of the system. The MATLAB/SIMULINK environment is used for simulation
supply powers for charging auxiliary power sources (e.g., battery modules). The Proposed circuit was simulated in PSIM with input voltage of 12 V; the corresponding output voltages obtained
This control scheme has the advantage of good stability and strong regulation capacity. The simulations are done in the MATLAB/SIMULINK. The graph shows that voltage is stabilized
thesis, the performance of battery supported and self supported DVR configurations are studied using simulations. The Synchronous Reference Frame (SRF) method is used for sag detection and the method ... unit vectors is…
provide controlled and regulated ac output. The AC-AC converter is designed and simulated using MATLAB 2010 and waveforms are analysied. Simulation results demonstrate that the output voltage
reduced. The system employing FOC of induction motor with space vector pwm was successfully simulated in Matlab and the results were verified. The proposed system shows effective response to even
will improves the drive performance by reduction of torque ripple, robustness against parameter variations. Simulation results are presented to validate the proposed technique
used to control the switches. To study the performance of the topologies, simulations has been carried out in MATLAB 2010 environment. It is compared with the existing inverter topologies; half
paper presents the simulation of the P&O and DC Link Capacitor Droop ControlTechnique for Solar Photovoltaic module using MATLAB Simulink. This MPPT techniques for a PV system ... merits and demerits. MPPT technique was…
measured and is found to be reduced by 45 percentage with LC filter. Simulation has been carried out to study the performanceof the proposed topology in MATLAB/Simulink R2010a environment
algorithm is used in this paper for optimization purpose. The proposed method is simulated on an IEEE 14 bus standard test system. The test system for the proposed method ... modelled and simulated using MATLAB/PSAT
with diode reverse recovery current and to achieve ZCS. Operational analysis, design procedure and simulation results for a 5HP, 500V, 1720 RPM DC motor is presented. The system show enhanced
addition to the two PI controllers that are used as the inner current controllers. Simulation and experimental results can be a testament for the effectiveness of the proposed technique
this circuit with a power of 166 W. It is proven by using MATLAB simulation
hybrid structure with and without third harmonic injection is analyzed in this paper by simulation in MATLAB/SIMULINK. A prototype of single phase topology is also developed
theoretical analysis is carried out for investigating the step-up voltage conversion ratio. The simulation is carried out here in MATLAB/Simulink platform. For demonstrating the effectiveness of the softswitching
type of loads and resultant THD with each type of loads are analysed. Simulations has been carried out in MATLAB/SIMULINK
zero current Commutation (ZCC) and the natural voltage clamping (NVC) has been analysed. Experiment simulated using MATLAB 2010.Ra and output power of 500W is obtained which is suitable
side harmonics. The switching frequency is set to 10 kHz. The simulation analyses are carried out in Matlab/Simulink software. The effect of APF and Buck-Boost circuit ... sinusoidal nature of line current are analyzed…
reduced conduction loss and low input current ripple. The operating principle and MATLAB simulations are discussed in detail
system. Waveforms of voltage, current and the power flow is analysed. The simulation platform used is MATLAB/Simulink
module’s grid connection through a dc–dc boost converter. The converter is simulated with low dc voltage input for low power applications. A 15V input voltage, 200V output voltage ... between the normal booster PV model…
pulses. Feedback circuit is provided with PI controller for accurate result. The converter is simulated using MATLAB 2010 and waveforms are analysed. Simulation results demonstrate that the output voltage
each RAPS component have been developed for effective management of the RAPS components. Through simulation studies carried out using detailed model in MATLAB Simulink, it has been demonstrated that
Modified NAGT method obtained by the above modifications is simulated and compared with efficiency curve obtained from load test and AGT method. Winding health estimation is done by using negative
For authors and organisers
Find the right journal for your paper and submit your manuscript.