loadings, factor extraction from a uni-diagonal matrix, reduced items, fitness indices etc. We used SPSS and AMOS version 25 exploratory and confirmatory factor analyses to develop YPOS. To test
changes, histopathological lesions, pathogenic loads, cellular and humoral immunity levels, the expression levels of IFNs, pro inflammatory cytokines, as well as anti-inflammatory cytokines were tested. Co-infection…
unpredictable and the non-invasive diagnostic tests – including ECG, echocardiography, MRI, and serological tests - are limited in their ability to make a clear cut diagnosis, all patients with clinically suspected…
unpredictable and the non-invasive diagnostic tests â?? including ECG, echocardiography, MRI, and serological tests - are limited in their ability to make a clear-cut diagnosis, all patients with clinically ... active…
diet. Statistical differences were analyzed by SPSS using independent samples t-test with p-value < 0.1 as a level of significance. From results, the decrease in proportions of many saturated ... exposure but some of…
yield of 85% with bare SnO2 on mayenite with 6% wt of a catalyst load in respect to oil, 60°C of a temperature, and 4:1 of a methanol ... were used to determine the state of the catalysts after carrying out the aging…
responsible for better joint strength than joints welded by 3S wire. Tensile tests results showed joint strength due to 4N wire to be slightly superior (by 3.5%) to joint welded ... joints showed softer Heat Affected…
Construct validity was done by exploratory factor analysis and all 13 items loaded in two factors. Concurrent validity was checked by calculating Pearsonâ??s correlation between the tool and Bradenâ ... found to be…
composite polymers. Injection moulding technique was employed in their production process. Filler material loading varied between 0-20% and 0-10% for rice husks and coffee husks respectively. Biochemical analysis…
composites with GO loading ranging from 0 wt.% to 2 wt.% are prepared by using a melt compounding method. The samples for characterizing and mechanical testing are shaped by injection ... increased by 27.4%, 31.3%, and…
buildings in high wind and seismic zones. Extensive experimental investigations, including monotonic and cyclic tests on cold-formed steel shear walls with corrugated steel sheathing, were recently completed ... seismic…
second part is devoted to the experimental study of repaired damaged concrete loaded under compressive tests. Three different damage rates are applied to the concrete before the reparation. For damage
practice, transient creep can be described accurately enough by the concept of LITS (Load Induced Thermal Strains), which is defined as the difference between the total strain, measured ... thermomechanical and…
performance of aged column structures. To confirm the effectiveness of the strengthening method, static loading test, impact test, and field test were performed on test specimens for short-span steel ... made for both…
ONESIDE blind bolts and LINDAPTER blind bolts, and experimentally tested to investigate the panelâ??s response to static railway design loads. The two blind bolts and the static experimental methodology
stressing method. The test results from four-point bending also revealed that using pre-stressed CFRP led to higher flexural stiffness, reduced crack width, postponed yielding load, higher ultimate load
severe loading conditions or had been built based on old standards. One of the most common methods of assessment is the use of Non-Destructive Test (NDT). Handheld ... maximum load capacity. Hand-held NDT and robotic…
frame specimens, including five corroded frames and one frame without corrosion, were tested under quasi-static cyclic loading. The corrosion ratio of longitudinal reinforcement and the axial compression ratio were…
second part is devoted to the experimental study of repaired damaged concrete loaded under compressive tests. Three different damage rates are applied on the concrete before the reparation. For damage
practice, transient creep can be described accurately enough by the concept of LITS (Load Induced Thermal Strains), which is defined as the difference between the total strain, measured ... thermomechanical and…
horizontal loads. The bolted-flange connection was used for square steel tube structural column in the high-rise structures. To study its mechanical properties, full-scale model tests and finite
group of demountable shear connectors with different stud collar size have been push-out-tested based on Eurocode 4 to assess the potential and suitability in terms of replacing welded ... shear studs for this…
between web shear deformation and local flange bending. The numerical models were verified by tests. By using the numerical models proposed, the static service behaviour, dynamic properties and long-term…
wide-flange beams with three different configurations, namely Standard, Narrow and Tuck. The test specimens were loaded in a displacement control mode using hydraulic actuators in accordance with the Chapter ... beam to…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.