this context, several studies also focused on different parameters which affect the mass transfer coefficient Kla such as agitation, temperature, nature of the regime (batch or continuous), current density applied
form copper nanowires and the subsequent reaction with Au3+ at different temperatures of 140, 220 and 300 °C. This is to achieve their synergistic effect through the combined
mini spray dryer at constant air inlet temperature of 150±2 °C and outlet temperature of 55±3 °C. The viable cell counts of the microcapsules were determined during their ... variants of white bread, moisture contents…
obtained and analyzed. A known problem of heat conduction between two plates with different temperatures but with the nonequilibrium condition in one of them (namely, in the left boundary ... same. At the boundary the…
Charpy impact samples were tempered at each of these temperatures. These samples were separated into uncharged and hydrogen charged samples. The charged samples were then plated with ... charging exhibited lower impact…
produce dual matrix (DM) DI is accomplished by two different methods, which are: the isothermal holding in the inter-critical temperature range after austenitization and the direct heating to this
thin-walled castings with 5mm wall thicknesses. In this work an influence of three different master alloys was investigated, namely ... Tmin - the minimum temperature at the beginning of α (Al) solidification) of an…
brief introduction of the process has been presented alongside a depiction of the different steps involved in product development. The process is a mix of overlaid item fabrication and brazing ... thick metal foils…
parameters and macrograph of the weldment. A bead-by-bead deposition model and two different lumped models were used for analysis. The results obtained by these models were validated ... maximum residual stress in…
associated with the change in the point defect structure whereas the composition determined high temperature wear performance of coatings. The study shows that in situ synthesis allows tailoring coatings ... This is of…
production of octane boosting ethers e.g. MTBE and ETBE are thermally unstable at temperatures above 100oC, decompose to corrosive products that cause environmental problems. Zeolites are known to be potential…
theory is used to understand the nanoparticle interaction with the pore walls at different ionic strength, temperature, and pH. For the case where the total interaction is repulsive, where ... assumed to be monolayer…
protonated aminopyridinium cation) was synthesized and characterized by X-Ray diffraction at room temperature, DTA-TG measurement, FT-IR and FTRaman spectroscopy and optical absorption. Its crystal structure ... packing…
correlations with water temperature, rainfall, water depth and size of water bodies. In addition, we will discuss the factors regulating the distribution of aquatic insects in different seasons
each exogenous proteinase. Additionally, exogenous enzymes varied in their ability to enhance hydrolysis of different feed ingredients. In conclusion, P. muelleri by-products are the best candidates to be employed…
September 2015. A total of 7 species of bivalves were identified in 20 different areas throughout the lagoon. Seven species of bivalves belonging to the four genera Gafrarium, Meretrix, Saccostrea ... species…
concentrated in zones where excess rainfall, together with high and/ or extreme variation of temperatures occur, which induce biological contaminants (insects, mites and fungi - including toxigenic strains)…
their stability and protect them against oxidation, light, moisture and temperature by acting as barrier. The effect of different coating materials, core/coating material ratio and various dying temperatures…
around 5.79-5.98. Time to reach optimum pH (around 3.9) was investigated at different fermentation temperature (4°C and 20°C). It was required more time (13 days) to reach ... optimum pH regardless of samples. When it…
dose. Differential scanning calorimetry (DSC) thermograms showed that there was no significant difference in the gelatinization temperatures, as well as the corresponding transition enthalpy. Microscopic observations…
This study was conducted to investigate the effects of different fat replacers (i.e. inulin, 0, 2.5, 5 and 7.5% w/w; maltodextrin ... that the creamer containing 25% maltodextrin and 7.5% inulin exhibited the highest…
test a multimechanism energy harvesting device to harvest energy from mechanical vibrations using two different mechanisms viz. Piezoelectric Effect and Faradayâ??s Law of Induction. In this study, we have ... used to…
glass transition temperature (30oC). The objective of this study was to assess protein secondary structure of zein during dough mixing at 40oC. The effect of different additives (hydrocolloids, cross-linking
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.