modeled as elasto-plastic Mohr Coulomb material model coded with stress dependent hyperbolic soil modulus model under static loading and non-linear hysteretic constitutive model that follows the Massing rule ... wrap…
measured, NDFX-A and NDFX-B displayed similar behavior as gauged by viscosity and shear stress. NDFX-C produced a large flow curve, with a larger area under the flow ... curve than NDFX-A or NDFX-B. Measurement of…
Sneddon theory of ISO with unphysical exponent 2 on h lacks these possibilities, disregards shear-force work, and violates the first energy law since 50 years. The denied but strictly ... joint maximal force to the…
biocompatible qualities of biomaterials, our proposed solution called “Ortho-metamaterials” will match the elastic modulus, hardness, fatigue resistance, porosity and notch-sensitivity of natural bone. Using our own…
doughs were viscoelastic in nature, with a storage modulus greater than the elastic modulus and a loss tangent less than 0.5, indicating the elastic behaviour of dough. The pearl millet ... viscosity during the heating…
modulus (low Tg) underfill wereabout half the stresses of the design with high-modulus (high Tg) underfill, and this was true for both thin (0.05 mmthick) and thick ... somewhatlower normal stresses, than thin layers…
extra screw above the fracture gap can cause a dramatic reduction in the shear IFM. However, since axial IFM mainly occurred as a result of bony fragmentsâÂ?Â? tilting, insertion ... micromotion, the proposed design is…
radiation hazard. One potential marker that has gained interest is tissue elasticity, evaluated using Shear-Wave Elastography (SWE). The purpose of this study was to assess the potential of using…
thin layer of carbon, has a large specific surface area, high YoungâÂ?Â?s modulus, high thermal conductivity and excellent electrical conductivity. These properties make graphene one of the most ... addition of…
atomically thin layer of carbon, has a large specific surface area, high Young’s modulus, high thermal conductivity and excellent electrical conductivity. These properties make graphene one of the most ... addition of…
this analysis, fatigue behavior of Aluminum foam has been discussed, and inter-laminar shear stress between single-walled carbon nanotube reinforced aluminum foam and multi-walled carbon nanotube reinforced aluminum…
necessary in order to improve stress transfer between polymer matrices and nano-fillers. Shear-crystallization and gel-spinning under flow were combined to fabricate polymer/nano-carbon composite fibers with…
gels and here we present data on the new tests such as constant shear at different temperatures; cross-over temperature/gel point; cohesivity, adhesivity and hardness; fitting to Burger ... different stages of hydrogel…
grids that allow for high density and high-quality chronic recordings, which reflect the modulus of the brain better than either traditional metal or silicon-based electrodeshave created a flexible ... brain caused by…
strength of composites decreased significantly by inclusion of these fillers. The flexural properties, interlaminar shear strength, compressive strength, density and hardness were also affected by the type of content…
properties vary with the size of the bubbles and measurements were made on controlled shear/stress rheometer. CLSM accompanied with image analysis technique, was used to obtain microstructure ... been taken into…
properties vary with the size of the bubbles and measurements were made on controlled shear/stress rheometer. CLSM accompanied with image analysis technique, was used to obtain microstructure ... been taken into…
reinforced with low SBM contents (2.5 and 5 wt%) presented high values of flexural modulus and strength, while the blend reinforced with higher SBM load (10 wt%) showed higher elongation ... modified SBM/epoxy…
control groups containing a prepared and a commercial fissure sealant. Flexural/micro-shear bond strength values were measured using Zwick test machine. Cavities on sixty healthy premolar teeth were filled ... analyze…
effects of the nonlinearity coefficient of elasticity, variation of the radius and the Young modulus. The model described characterizes the blood flow consecutively in aneurysms, stenoses and prostheses. We obtain…
examined by three-point bending tests, which showed that the scaffolds had anisotropic bending modulus (21.9±4.1 kPa with curvature VS 39.3±3.6 kPa against curvature). A finite element approach ... which direction it…
examined by three-point bending tests, which showed that the scaffolds had anisotropic bending modulus (21.9±4.1 kPa with curvature VS 39.3±3.6 kPa against curvature). A finite element approach ... which direction it…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.