surface structure of biomaterials is critical for the processes that took place at the interface between biomaterials and simulated body fluids, whether or not enriched with proteins. In order ... tune the surface…
powder is sprayed onto a grounded substrate. . In case of wood and wood composites, the limited electrical conductivity constitutes a disadvantage. Pre-heating or priming process with an electrically conductive
identified as spray rate, inlet temp, atomization air pressure & air flow in fluidized bed processor to obtain required size of granules. Air flow range for the process was decided
micromixer-assisted nanoprecipitation process was used to get and to easily tune the size of Ketoprofen-loaded PMMA nanoparticles (100-200 nm). Combined with a commercial spray dryer, dry-state
where the ionization process occurs outside the mass spectrometer, in open-air environment. Generally, they are simple and provide direct analyses. Here, ambient ionization techniques (Paper Spray, EASI and DESI
results indicate the higher resistance of as-sealed coatings compared with as-sprayed coatings to the hot corrosion. Degradation due to the presence of eutectic harsh salt attack was occurred ... lower yttria content is…
preparation of self-cleaning formulations. The aqueous formulations were applied in a dip-coating process to different textile fabric blends. The intended benefit from such nano-structured ZnO clusters ... water contact…
measures, to take care of day to day factors causing cellular injury and inflammatory processes. Traditional foods and traditional therapeutic systems the world over including Ayurveda point to the benefits…
work the process chain of powder-based inkjet-3D-printing is presented. This includes the production of bioceramic suspensions from bioglass, calcium phosphates and composites and spray dry granulation
improves drying processes by intensifying heat and mass transfer. Indirect implementations of this technology involve the ultrasonic waves as parts of drying systems such as nozzles of spray-driers
spray deposited film shows band gap 2.87eV. Prepared thin films then applied to the photocatalytic experiment of reduction of Cr (VI) from aqueous solution. Various process parameters have been
various animal models with reduction or absence of fibrosis resulting in a regeneration process. The RGTA technology validated in many preclinical studies is now marketed as human healing agents ... closure and with no…
protein source and as a wall material for encapsulating sensitive nutrients, most commonly by spray-drying. There has been a recent trend of partially replacing milk proteins with vegetable proteins ... supplement…
immune system attacks and destroys the beta cells. This type involves the processes of betaâ??cell destruction, which results in absolute insulin deficiency.It occurs at the age of less than ... weight loss, Increased…
carried out to evaluate control points in a pilot plant designed for sugarcane juice processing. The juice was extracted in a stainless steel electric cylinder mill and then acidified with ... unidirectional air-flow…
radiation-processed oligo-chitosan on post-harvest loss of litchi fruit was investigated. Different concentrations of irradiated (40 kGy) chitosan solution (500, 1000 and 1500 ppm) were sprayed on litchi
processes. It includes new method of storage of food at low temperature & it is mainly for egg. Canning technology through optimization & modeling techniques. Recent advances in agglomeration in spray drying
food industry to develop alternative methods that ensure the microbiological safety of minimally processed foods while preserving original quality characteristics. In this context, atmospheric plasma treatment…
other hand, the columnar Ca1.95Eu0.05Si5N8 particles could be obtained when the spray-pyrolyzed powder was heated to 1100Ã?ºC at the rate of 30Ã?ºCâÂ?¢min-1 and then ... morphological control was conducted by the kinds…
using industrial and environmental by-products; these materials can be refined using simple chemical processing and can be deposited through direct patterning using lowcost additive manufacturing. Resultant active…
tract, microencapsulation has been used. The aim of this work was to optimize a process of microencapsulation of chicozapote (Manilkara sapota) pulp and mamey (Pouteria Sapota) pulp and the probiotic ... central points…
still limited. Therefore, the aim of our research was to develop sustainable formulation process and evaluate biological activity (in vitro bioavailability and antioxidant activity) of dry polyphenol rich olive pomace…
processed and selected sub fraction was subjected to fresh column chromatography. Washing was continued till TLC shows a single spot observed under UV at 254 nm and 366nm after spraying
process, in which the API is dispersed and or dissolved into a polymeric matrix. HME is an excellent alternative to other conventionally available techniques such as roll spinning and spray
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.