electronic devices, a high density solid material is needed, instead of a nanoparticle powder. Classic sintering processes, however, lead to a rapid grain growth and hence to the loss ... with the nanometric range…
characterized SSP was hydrolyzed at pH = 9 (employing sol-gel method) and the resulting powder were sintered at 450°C for 4 hours. The XRD pattern of the hydrolyzed product ... Pb3O4)) and ZrO2. The morphological…
between the grains dominates the dynamics over the random thermal motion. Using mono-disperse powder and plane-parallel electrode radio frequency discharge, one can easily form stable single layer
conditions, including dynamic loading. In the process of laser cladding with coaxial feeding of powder to transport the gas generates a stream surfaced filler material that melts under the influence ... occurs bath…
fullerene molecules and their transformation into superelastic hard carbon particles in the metal powder and simultaneously consolidation of the powders into CM samples of 5-10 mm in diameter
inorganic particles. According to this fact ultrafine and nanopowders are of special interest. UHMWPE powder (2 million g/mol) was used as a polymer matrix. As a reinforcing phase ... used alumina Al2O3 of 2 types…
AUsCitoFen quasicrystal composites samples were produced by consolidation of mechanically alloyed powders. For composites preparation the quasicrystalline powder was milled together with different kinds of metallic…
impurity phase prior sintering providing a material of pure perovskite phase for further powder processing. A multistep firing protocol is proposed with ball milling intervals. Two intermediate thermal steps
Powder-based inkjet 3Dprinting method is one of the most attractive solid free form techniques. It involves a sequential layering process through which 3D porous scaffolds can be directly produced ... quality are…
prepared by thermal evaporation process (Physical vapor deposition), from the nanocrystallines CuFe and CuFeCo powder obtained by mechanical alloying After 24 h of milling from elemental powders. The structural…
Tantalum (Ta) element with the aim of producing nanostructured intermetallic alloys from elemental powders by means of mechanical alloying (MA). The phase evolution and microstructural changes of the powders during
dispersabilities in aqueous and non-aqueous fluids, particle size and magnetism of the nano-powder materials. The possibility of recycling the beads and reclaiming the oil is also demonstrated. These
orthovanadate, Ba3-3x/2(VO4)2:xEu (0≤x≤0.3) are reported. X-ray powder diffraction (XRD) of the annealed sample indicates that rhombohedral Ba3V2O8 with small amount of EuVO4
lithium titanium oxide (Li4Ti5O12) - anode material using grapheme oxide. The pristine nanocrystalline LiMn2O4 powder was synthesized by modified sol-gel method. The pristine Li4Ti5O12 was synthesized by three-step…
second ceramic phase. Additives in both nano- and micro-scale dimensions (as fine powders or in the form of fibers) were introduced mainly to block the bubbles from moving
heat treatment. The crystalline phase formed after heat treatment was identified using X-ray powder diffraction technique. Bioactivity of these glasses was measured before and after immersion of glass samples
Good wear resistence; surface roughness retention; anti-slip; antiadhesion foreign objects; anti-adhesive zinc powder. In the early 1980s, the general use of the chrome plated rollers, improve the wear
ZnFe2O4. The sensing materials were characterized by SEM, XRD and UV-Visible spectroscopy. The powders synthesized materials were compacted in to pellets using hydraulic press. Thick and thin films
composition of supernatant solution, i.e., lead content was found more than cobalt content. The powder XRD suggested the orthorhombic nature for all crystals. The grown crystals were characterized by FTIR
prepared by sol-gel route using solutions of iron nitrateand bismuth nitrate. The produced powder was dried at 150ºC for 2 h and then calcined at various temperatures
standard reference for this model. Shade dried leaves of Musa Paradisiaca(Linn.)were powdered and subjected to Soxhlet extraction using alcohol and water. Hydroalcoholic extract was administered to the animals
Klebsiella pneumoniae and to identify the most active fraction of them. The rhizome’s powder was macerated with 96% ethanol, then the resulting extract was evaporated and fractionated by vacuum
structure of the copolymer was systematically studied by IR, NMR and X-ray powder diffraction (XRD) methods and the surface morphology with SEM analysis
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.