commercial Magnum H50, Co64Cr29 Mo6.5A0.5 (A=C, Si, Fe, Mn), alloy. Vickers hardness and roughness parameters of Co-Cr based alloy varied after aging in saliva for a different time
respectively. The wind shear exponents and roughness parameters were analysed and found to be 0.1652 and 0.0374 respectively. Weibull scale and shape parameters were obtained using Weibull-fit, Regression
interfacial properties such as entropy of fusion per unit volume (DSV), interfacial energy (s), roughness parameter (α), grain boundary energy of parent components, eutectics and non-eutectics have been studied
titanium biomaterial was changed after exposure to magnetic resonance imaging (MRI) and gamma radiation. Roughness parameter (Ra) was significantly increased after exposure to magnetic resonance imaging and gamma…
andC=0.01%) dental alloy has been studied. The results showthat,Vickers hardness, roughness parameters, corrosion resistance and corrosion rate of Protechno® -N alloy changed after exposure
experimental investigation was conducted to determine the main machining parameters which contribute to material removal rate (MRR) and surface roughness (SR) in wire-EDM of mild steel. In WEDM operations ... essential…
research, an attempt has been made to experimentally investigate the effects of cutting parameters on surface roughness in hard milling of AISI H13 steel with coated carbide tools. Based ... speed and the feed are the…
optimum cutting conditions to get lowest surface roughness in turning by regression analysis. To investigate the effect of cutting parameter like spindle speed, feed rate and depth ... using Surfcom 130A.Multiple…
performance is indicated by surface quality. The determination of optimum cutting parameters achieving better surface roughness is a matter of research for the past few decades.Lot of studies are going ... measured with…
machining parameters were investigated using Taguchi L18 orthogonal array. Optimal cutting conditions were determined using the signal-to-noise (S/N) ratio, which is calculated for average surface roughness ... variance…
machine impact on product quality and productivity of the process. For the analysis input parameters like feed rate, spindle speed and depth of cut selected as a control factors ... were performed to find out the…
Inclined broken roughness was designated as the (optimized) roughness to experimentally investigate the enhancement of thermohydraulic performance. This research concentrates on the Fuzzy Inference System (FIS) as an…
main objective of this work is to evaluate the best WEDM process parameters for machining 18-4-1 grade High Speed Steel (HSS) of different thickness ranging from ... power. The material removal rate (MRR) is computed…
This paper deals with finding optimal control parameters to get the minimum Surface roughness. It considers the analysis of effect of the process parameters, cutting speed, feed rate and depth
mechanical concepts via a principle scale dependent accessibility with respect to input parameters from measurement, surface roughness or even non-continuous composition, one does not only overcome such flaws
biological and chronological age ratio, frailty index, frequency of aging symptoms, viscoelastic parameter skin, roughness, radiance and uniformity of hand skin tone. Evaluation results of hand, neck, décolleté and face
This project is conducted to investigate the effects of these variable parameters on depth of cut and surface roughness of various materials. As a result of this study ... parameters have direct effect on depth of cut…
baseline and after 2 months. The software of the device automatically calculated the roughness index (a parameter linked to fine wrinkles) expressed in mm. Primary outcome was the evolution ... tolerated. At baseline…
four machining parameters including spindle speed (N), feed rate (f), depth of cut (d), and various percentage weight of silicon carbide (S) on surface roughness (Ra) was studied. The concept ... experimentation. The…
nodal concentrations etc., are normally crisp values assuming crisp input parameters. There are many uncertainties in nodal demands, roughness, length, diameters of pipes, valve operations, water levels in reservoirs…
electrochemical polishing. The process variable parameters considered are electrolyte temperature, current density and electrolysis time. The two methods are employed for measuring the surface roughness ... first method…
experiments were conducted by changing levels of cutting parameters (spindle speed, feed rate and cutting depth) in CNC turning machine. Surface roughness of the work piece has been depended ... surface roughness of the…
This report presents an experimental investigation on the change of output parameters especially surface roughness during machining aluminum alloy 6063 using minimum quantity lubricant (MQL) technique. The minimum…
feed. The Taguchi method is applied to study the performance characteristics of machining parameters with surface roughness (Ra), cutting force and tool wear rate. By using Taguchi analysis, optimized process
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.