green bodies could be measured and observed by using a digital optical microscope. The microstructures of the sintered components were observed using a scanning electron microscope. Relative densities of these
from flakes to slender wires were obtained as shown in Figure 1. The flaky microstructure is attributed to presence of PEG that acts as a stabilizer, dispersant while mild heat
surgical repair of carotid arteries.D. Retraint, Z. Quadir, W. Xu, L. Waltz, M. Ferry, “Microstructural investigation of roll bonded nanocrystalline stainless steel sheets”, The 16th International Conference on the…
homogenizing treatment and extrusion process, with regards to serving as a biodegradable implant. The microstructural characteristics were examined by optical microscopy, scanning electron microscopy (SEM), and X-ray…
particle energy, SRIM (The Stopping and Range of Ions in Matter) figurings were done. Microstructure and stage arrangement of adjusted filaments were concentrated by methods for examining electron microscopy
based grain scale geometry was generated by taking full advantage of true grain scale microstructure information. Secondly, Strain gradient parameters was obtained through CPFE based simulations. Thirdly, dynamic…
sintering temperature. BTH ceramics resulting from spark plasma sintering at 1050oC/2min have dense microstructures(relative density 96.3-98.2%)and fine granulated. Increasing the Hf content induce a slight decrease…
development of nanostructures in steels, such as nano twins, deformation-induced martensite, ultrafine-grained microstructure, nano-sized intermetallic phases, short-range ordering, etc. A complex interplay of…
nanoparticles. The optical and scanning electron microscopy (SEM) will used to study the microstructure of samples, as well as to investigate the size and morphology of the reinforcement powders. Moreover
minimum wear and coefficient of friction for jute fiber reinforced laminates were analyzed. The microstructure behavior of the fabricated samples were investigated with assistance of Scanning Electron Microscope (SEM)…
under a pressure of 80 MPa. Microstructural changes and phase constituents of the powders before and after consolidation were mainly characterized by X-ray diffraction (XRD), scanning electron microscopy
grain size and, thus also, nature of the secondary phases are the most discriminating microstructural parameters. Moreover from the tribological point of view, the dielectric characteristic of materials (breakdown…
grown edge exposed layers using DC magnetron sputtering technique. To understand a correlation between microstructural and material properties, we have been prepared the MoS2 of varying thickness
discharge 7 % of total worldwide CO2 emissions annually. However, owing to the porous microstructure, the durability of cementitious materials (cement paste, cement mortar, concrete) is still a big issue. Much…
confirm the phase purity and morphology, respectively carry out the structural and microstructural characterization. Low temperature annealed Ni1-xO appears black in colour and absorbs a fraction of light
high porosity and interconnected structure of macro and micropores. The morphology presents a eutectoid microstructure of lamellae type, composed of alternating layers of silicocarnotite and α-tricalcium phosphate.The…
also being used in recent studies to ensure mechanical compatibility among topology optimized microstructures This would simultaneously optimize the physical properties of the individual cells as well as those
sizes were dispersed into Mg powder using high-energy ball-milling (BM) processes. The microstructure of the fabricated composites was characterized using transmission electron microscopy (TEM), scanning electron…
copper cold spray coatings is provided. Particular attention is then given to the unique microstructurally mediated pathway of copper ion diffusion associated with copper cold spray coatings that enable fomite
considered to be a clay matrix that embraces silt and sand grains. An available microstructure- based model of the clay matrix shrinkage curve is used. For data analysis we derive
successfully developed via in situ oxidative polymerization of aniline monomer. The microstructure and morphology of the prepared composites were characterized by using Fourier transform infrared spectroscopy (FTIR)…
films (2-10 nm) grown by dc magnetron sputtering. By performing raman mapping analysis, microstructure analysis, absorbance measurements and density functional theory (DFT) calculations, we gained deep insights into
molybdate nanocomposite was successfully assimilated via in-situ oxidative polymerization of aniline monomer. The microstructure and morphology of the prepared composites were characterized using several techniques…
respectively, whereas the crystal structure cycles between the twinned and ordered parent phase structures. Microstructural mechanisms responsible for the shape memory effect are the twinning and orientation processes…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.