powering the robots for surveillance is difficult this project provides a solar powered mobile microcontroller based surveillance platform which is an amicable solution to the problem. The project involves…
measurement system of 3 phase power supply system using MAXIM chip MAXQ3183 and Philips microcontroller P89V5RD2. Hardware is created to sense the voltage and current from three phase supply ... MAXIM chip. Further…
This project proposes an innovative design to develop a system based on microcontroller that is used for monitoring power of a distribution transformer in a substation and to protect ... transmitter in the substation is…
endeavour to optimise the consumption utilising the modern electronic system developed using microcontroller. Here the energy audit is conducted, the area identified, some energy efficient appliances recommended and an…
Home & Industries [6]. The system is fully controlled by the 8 bit P89V51RD2 microcontroller. All the sensors and detector are interconnected to microcontroller by using various types of interface circuits…
then converts these changes into a digital signal that can be read by a microcontroller. The DHT11 sensor uses a single-wire interface to communicate with the microcontroller. The sensor ... sends a signal to the…
blocks is used to deploy the pre-trained deep CNN model onto a PIC microcontroller. TTL is used to connect the output from the MATLAB software in the personal computer ... microcontroller. The PIC microcontroller is…
ions in solution both continuously and nondestructively. This work presents the development of microcontroller based Instrumentation system to measure the sodium-potassium and concentration in vegetables by using an…
single-phase digital energy meter with self-calibration technique based on PIC16F84A microcontroller for monitoring the consumed energy of any load with high accuracy and stability. The design
behavior of stoves or heating systems was set up by programming an Ardiuno Mega microcontroller, provided with type-K thermocouples, LCD Display, SD card module, LM35 and DHT22 sensors
this research project, we mainly focus on designing and developing a prosthetic hand using microcontrollers, sensors and feedback for physically challenged. The control and movement of prosthetic hand will
sensor the resistor decrease with the force to measure the press force of finger, microcontroller (atmrga8) to process signal from sensor and calculate the force for every finger, LCD display ... display the result from…
construction of an intruder detecting and alerting system. This was achieved using an AT89C52 microcontroller for the control of the other component, a SIM900-GSM module that communicates between ... sensor (motion…
systems were designed for the robotic arm: Programmable Logic Controller (PLC) and Arduino UNO microcontroller. It employed open loop control with PLC at first and closed loop PID control using ... difficult to achieve…
Proteus software is being used to design the circuit for the Arduino UNO microcontrollers and H-Bridge IC chip. This implemented system can save more energy and probably offers more
across the globe. The work was achieved with the aid of a specially designed microcontroller (PIC18F2550) that communicates directly with the mobile phone and some components like Schmitt Inverting Gate
handled by the current sensing circuit which is in the main board and microcontroller in the front board. The corresponding information will be displayed in the display unit
time data transmitting unit. This unit contains RTC and it is interfaced with microcontroller can display the running time accurately through 7- segment display. This time data is transmitted continuously
module, LDT0-028K vibration sensor, RF Transmitter and Receiver and Arduino Mega 2560 microcontroller. The developed telematics module demonstrates the feasibility of near real-time tracking of vehicles and improved
phone book. The messages are typed into Braille keypad and are processed by microcontroller which converts the Braille letters to English alphabets using the look up table then this
proximity sensor senses the presence of the fruit and it is interfaced with the microcontroller 89C51 and the process continues as per the program. The maintenance of the system
mobile. To keep it simpler, this paper will tell you how to interface a microcontroller (ATMEGA328) with CAN (Controller Area Network) bus, hence communicating with the car and performing operations
module. Depending on the received signals the robotic arm which is followed by AVR microcontroller performs the receptive motions at the receiver section
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.