Objective: The study compared 2 Light Emitting Diode (LED) curing units with a universal testing machine for checking the shear bond strength and also evaluated adhesive remnant index (ARI). Methods
fibers. The analysis of mechanical properties of the PHB/CNTs composites by using universal testing machine (UTM) revealed great improvement over pure PHB scaffold, so that the tensile strength
fibers. The analysis of mechanical properties of the PHB/CNTs composites by using universal testing machine (UTM) revealed great improvement over pure PHB scaffold, so that the tensile strength
testing. Each Sample was investigated using pushout test by placed them in a universal testing machine at a crosshead speed of 0.5 mm/min. Results: The highest Bonding strength wasshown
cylinders and autofrettaged FML cylinders were subjected to radial compression in a computerized universal testing machine of maximum capacity 600 KN. The compressive strength and aspect ratio
reinforced composites were measured using a horizontal burning test, thermo-gravimetric analyzer, and universal testing machine, respectively. The composites were fabricated from epoxy resins and coconut shell particles…
permeability sandstone and shale formation. The fracture was created using the universal testing machine with the help of core sleeve and then tested for prediction. Around 30 sidewall core samples
cyclic fatigue tests of each overdenture were measured using BENDAO tools of the universal testing machine and average reading was calculated. Result: (Group I) mini-dental implant overdenture with palatal
tested placement molds (n=20) and SBS tests were performed using universal testing machine. Results: The findings showed that bond strength was not influenced by different composite placement molds
tests. Validity of optical strain-measurements is assessed against the results of an universal testing machine, a good correlation was found by comparing the results
characterization of fabricated film was investigated through Fourier Transform Infrared Spectroscope (FT-IR), universal testing machine (UTM) and water-contact angle. Furthermore, cytotoxicity and anti-inflammation of…
under compressive load at a crosshead speed of 1 mm/min using a universal testing machine until fracture occurred. Recorded data were statistically analyzed using one-way analysis of variance
water (control group). After conditioning, the flexural strength values were assessed by a universal testing machine. The standard three-point bending test was conducted on the specimens at a crosshead
subdivided into two halves based on thermocycling. Shear bond strength was measured using Universal Testing Machine and then the samples were observed under magnification (80X) using a Stereomicroscope to identify
degree and 45 degree of WNS and tested under a UTM (Universal Testing Machine) analyzed. Tensile strength and flexural strength were investigated. An increased Tensile strength was observed with increase
modified SiC/ waterborne polyurethane composites. By using FI-IR, XRD, SEM, TG, universal testing machine to test the analysis. Experiments show that nano-SiC can improve the mechanical properties
standards specified in ASTM A706. The measurements were carried out by using an universal testing machine model MTS 810. To determine the critical factors on the dynamic response of reinforcing
restored with resin composite and were subjected to shear bond strength evaluation under universal testing machine. Results: Significantly higher shear bond strength values were observed in teeth treated with
strength and modulus of elasticity was done by three-point bending test on Universal testing machine. Most successful nano-modified materials were chosen for cytotoxicity assessment using L929
specimens were then subjected to a shear bond strength test using a universal testing machine. The modes of bond failure were determined using a stereomicroscope and a digital camera. Results
thermal properties of the biocomposite PVA/LEA/glycerol films were analyzed with universal testing machine (UTM), and thermogravimetry analyzer (TGA), and differential scanning calorimeter (DSC). Morphology and…
dual-cure resin cement (LR). SBSs were determined with a universal testing machine at a crosshead speed of 0.5 mm/min. Fracture patterns were evaluated by a stereomicroscope
configuration. The force at break of the lap welds was assessed on the Universal testing machine, weld fracture surfaces and weld cross-sections were also analyzed under microscope using reflected
glass-fiber posts. All specimens were mounted in acrylic resin. Finally, a Universal Testing Machine was used to apply tensile load to dislodge each post from the prepared postspace. Statistical
instructions and polymerized. All specimens were submitted to a tensile test using a universal testing machine and results were statistically analyzed (ANOVA, p<0.05, Tukey’s HSD test). Results
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.