different hydrophilic polymers like PEG and / or PVP-K25 resulted in the formation of amorphous powders having enhanced drug solubility and dissolution properties , even if much smaller amount of hydrophilic
method was developed for the determination of Crystalline phase in Cefuroxime Axetil amorphous phase using X-ray powder diffraction technique. Validation of quantification method was carried out with respect
manufacture amorphous solid dispersion (ASD) formulations of poorly water-soluble crystalline drugs. The amorphous state, with a higher energy than the equivalent crystalline form, typically confers significantly higher…
manufacture amorphous solid dispersion (ASD) formulations of poorly water-soluble crystalline drugs. The amorphous state, with a higher energy than the equivalent crystalline form, typically confers significantly higher…
Cefoperazone sodium (CPZ-Na) and its stability. Methods: To classify CPZ-Na into amorphous powder and crystalline, powder X-ray diffraction (PXRD) was used. To classify CPZ-Na crystal powder ... high performance liquid…
elemental powders, using a low-energy ball mill. The solid-solution hcp-ZrNiPd phase obtained after 25 h of the milling time transformed into a single amorphous phase upon ball ... milling for 100 h to 150 h. This…
using room-temperature high-energy ball mill [5]. Ultrafine powders of amorphous- and big cube-Zr2Ni phases were prepared by ball milling small bulk pieces of tetragonal-Zr2Ni alloy prepared ... melting technique. Small…
case of PXRD, powders with crystal phase produce diffractive peaks and powders with amorphous phase produce hallow pattern. In the case of DSC, the powders with crystal phase has endothermic ... peak because they have…
compared to the milled counterparts, respectively. Third, SPS coupled with semi-solid sintering of amorphous powder was proposed as a novel approach to fabricate high-strength bimodal alloys with ultrafine
been recently observed in three unrelated systems: (i) Inhomogeneous commercial and fabricated amorphous carbon powders synthesized with sulfur (a-CS) which exhibit pronounced peaks in their virgin ZFC curves
depending on which the isolation and quantitative determination were done. A fruitful product of amorphous powder was yielded with a concentration 5.7 μg/g, the structure of this compound
drug substance into a dosage form. Pure drug substances are usually white crystalline or amorphous powders. Before the arrival of drugs as a science, it had been common for pharmacists
reflection modes of optical spectroscopy. These are usually highly light-scattering materials, such as powders, amorphous solids, gels, smears and suspensions. Other difficult materials are those that are optically…
they can offer: Increased stability (physical, chemical), masked taste/odor, convert liquid forms into amorphous powders, new formulation, new routs of administration, patent extension increased shelf life
compound ISPE–2 (250 mg) and chloroform: methanol (95: 5) fraction yielded a white amorphous powder, ISPE–5 (20 mg). Quantity of ISPE–2 in MEIS was found
Besides, being used to reduce gastrointestinal drug irritation, convert liquid drugs into microcrystalline or amorphous powder, and prevent drug–drug and drug–excipient interactions, they have shown to display adjuvant
pharmaceuticals is limited due to the low drug-loading efficiency. CDs come in amorphous powders, and it is difficult to uniformly mix hydrophobic drug compounds and CDs with sufficient solubility
reflection modes of optical spectroscopy. These are usually highly light scattering materials, such as powders, amorphous solids, gels, smears, and suspensions. Other difficult materials are those that are optically…
after 2 hours of mechanical alloying treatment. The as-milled Bi0.4Sb1.6Te3 powders were further mixing with Ti50Cu28Ni15Sn7 amorphous particles to form Ti50Cu28Ni15Sn7/Bi0.4Sb1.6Te3 composite powders after 30 minutes…
EGFK are presented in Fig.1. After annealing at 500°C, the powder has an amorphous structure. Annealing the powder at 700°C led to the formation of the crystalline product
mixture was composed of a blend of pure calcite (CaCO3) and silica amorphous (SiO2) powder with 57% wt. and 43% wt., respectively. Then, the powder mixture milled by high energy
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.