carbonate sintering (LCS) and tape casting. This process allows the flexibility to produce copper double-layer structure consisting of a porous section with a wide range of porosities ... dense substrate. Here…
potential photovoltaic materials for thin film solar cell applications. Among these materials, ternary copper indium sulfide (CIS) thin films with a direct band gap of 1.5 eV match well with ... stoichiometry, we kept…
further increased interest in the chemistry and physics of complex ternary transition-metal chalcogenides. Copper chalcogenide materials are of considerable scientific interest because of their rich structural and…
High resistivity and lower peel strength were observed on the surface of the copper layer electroplated onto the electrolyte of no additive B. However, a uniform surface, lower resistivity ... additive B was used. Large…
adsorbed on the copper surface at open-circuit potentials, preventing copper from being corroded by forming a protective layer on its surface. IC and AAS analysis results showed that ... adsorb on the copper surface in…
Nanosized Copper-aluminum layered double hydroxides (Cu-LDHs) and Nickel-Aluminum layered double hydroxides (Ni-LDHs) were synthesized using co-precipitation method. LDHs were organically modified by long chain sodium
with a self-assembled monolayer (SAM) of octadecyltrichlorosilane (OTS) and then an active layer of copper phthalocyanine (CuPc6) was deposited on top of the films. The output and transfer characteristics
used for an optimized design of the pH sensor array. For fabrication, copper conductive layer tracts with pH sensitive gel casting, on a polyimide substrate have been used. Conclusion & Significance
coated CNTs and CNFs via electroless plating which offer metallization with uniform distribution layer of copper. The copper coated CNTs and CNFs were annealed at 250Ã
Thin film nanocomposite (TFN) membrane with copper-aluminium layered double hydroxides (LDH) incorporated into polyamide (PA) selective layer has been developed for desalination application
samples. In order to measure the electrical features of FETâ??s, an active layer of copper phthalo-cyanine (CuPc6) was deposited andthe output characteristics of the devices were investigated using
layer in thin film solar cells. In2S3 is primarily used as a buffer layer in copper-indium-diselenide, CuInS2 (CIS) photovoltaic solar cells. In the last decade, researchers focused
layers are needed. We developed a one-step synthesis of a 2D layered, crystalline, p-type copper sulfide5 by thermal annealing of a standard copper foil in an inert environment ... Itzhak, A., et al., Digenite (Cu9s5)…
treatment (60-80 °C) of precursors leads to slender wire morphology. The ratio of copper precursor (CP) and PEG solutions influences the morphology. While molarity ratio ... results in stacked flakes. When PEG is…
treatment (60-80 °C) of precursors leads to slender wire morphology. The ratio of copper precursor (CP) and PEG solutions influences the morphology. While molarity ratio ... results in stacked flakes. When PEG is…
been successfully coated by spin coating technique using copper acetate as precursor. The precursor was prepared by sol gel method. Single layered, three layered and five layered CuO thin films
parent phase field. Lattice invariant shear is not uniform in copper based alloys and cause the formation of complex layered structures, like 3R, 9R or 18R structures depending ... through 18 layers in z-direction in…
when the interface effects cannot be neglected (e.g., Copper film deposited on Silicon Nitride membrane). Unlike the composite materials with layer stacking along the direction of propagation of excitations
modulate band gap. In this study, we electroplate the ZnO seed layer to cover on the copper grid as the first step. Secondly, we adopt the hydrothermal method to grow ... been conducted. The TEM images indicate that ZnO…
Thermal Electric Generator (TEG) Cells, which were produced using single layer membranes of graphene, and placed upon a copper substrate. As the conversion efficiency of the thermionic process tends ... will just go on…
modulate band gap. In this study, we electroplate the ZnO seed layer to cover on the copper grid as the first step. Secondly, we adopt the hydrothermal method to grow ... been conducted. The TEM images indicate that ZnO…
Experiments on formation of nanoporous and germanium and silicon layers with silver and copper nanoparticles by low-energy high-dose ion implantation are observed. For this task Ag+-ion implantation ... silicon surface…
disk consisting of variable mixtures of aluminium powder (Al), aluminium phosphate (AlPO4) and powdered copper (Cu). Both binary and ternary electrode systems were produced. The ternary membranes exhibit greater…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.