side reactions and competitive adsorption of reactants. This research aims to optimize catalyst loading and reactor design to enhance selectivity in hydrogenation reactions. A systematic experimental investigation was…
reaction, the dramatic rate enhancement of copper catalyze azide–alkyne cycloaddition (CuAAC) at low catalyst loading in PEG-H2O media has been observed. The present method provides high to excellent
these supports was carried out. It was found that ligand structures significantly affected Pd loading, which followed the trend: SiO2-tbtm > SiO2-btm ~ SiO2-pytm. Moreover, the influence of different ... presence of…
membranes. We mitigated the impact of low-Pt loading on electrocatalyst durability in an electrode by studying and understanding ionomer-support-catalyst interactions, and electrode microstructure evolution at the…
improve the basicity and catalytic performance of ZIF-8, a series of K-loaded ZIF-8 catalysts (K/ZIF-8) were prepared by varying the KOH content from ... form glycerol carbonate (GLC). Various reaction parameters…
design optimizing four variables including reaction time, reaction temperature, methanol/oil molar ratio and catalyst loading in which case the yield was the required response. The 50-50 catalyst attained ... 70Ã?ºC…
spectroscopy, XRD, FESEM, EDX and H2-TPR analysis. The catalytic activity of 10% Ni loaded catalysts was found to be highest with 95.78% mixture conversion and hydrocarbons selectivity ... than 7.5% and 12.5% Ni loaded…
calcination temperature (700 to 900°C), DES loading (3 to 18 wt. %), WES catalyst loading (6 to 14 wt. %) on the conversion to biodiesel were studied. The yield of biodiesel ... methanol molar ratio of 1:10, a…
Effects of various parameters such as nature of lipase, speed of agitation, mole ratio, catalyst loading, temperature and reusability of catalyst on the conversion was studied and optimized. Overall conversion ... mole…
anode consisting of Ni-based composite electrocatalysts loaded on Ni foam substrate was developed and employed. The use of Ni-based catalyst reduces the cost of fuel cell without compromising ... anode delivered…
with a methanol to oil molar ratio of 12:1 and a catalyst load of 5% wt in respect to oil. Furthermore, catalysts with Li2O and SnO2 were synthesized ... biodiesel yield of 85% with bare SnO2 on mayenite with 6% wt of a…
Hinshelwood model. The results explained the photocatalytic degradation efficiency, which was increased by increasing catalyst loading from 1 g to 2 g. The degradation efficiency decreased with the increase ... catalyst…
diff erent Mg/ Al ratios in catalyst preparation, calcination temperatures of LDH, reaction temperatures, catalyst loadings and the molar ratios of dimethyl carbonate/glycerol, etc., which are critical factors…
degradation of crystal violet such as the effect of variation of pH, dye concentration, catalyst loading, light intensity and effect of addition of oxidants such as H2O2 & K2S2O8 and salts ... such as Na2CO3 & NaCl…
coupling between phenols and aryl halides. Good to moderate yields were obtained at a catalyst loading of 10−15 mg for C−O coupling. In case of reduction of nitroarenes ... maximum conversions of nitroarenes were…
optimum conditions for the oleic acid esterification were observed at 70 °C, 5 wt% catalyst loading and 6:1 ethanol to oleic acid molar ratio. The oleic acid conversion using ... findings show that low Si/Al ratio…
photocatalysts for the degradation of Victoria Blue-B dye. Effects of photo-catalyst load and substrate initial concentration on degradation of the dye in aqueous solution have been investigated. Maximum ... degradation…
substrates. We can accomplish epoxidation of simple alkenes with up to ca 99% ee. Catalyst loading may be as low as 0.1 mol%. The epoxidation reactions may be carried ... preparation of unstable reagents. The lecture…
general are very selective and require mild reaction conditions as well as low catalyst loadings. Th e atom economy of these synthetic procedures is often 100% indicating that ... diacetoxy-2-butene (2) using…
light in aqueous solution has been studied. The operational parameters such as dye concentration, catalyst loading, pH and light intensity were investigated during the process. The experiment was carried ... observed in…
based on a range of control experiments, works effortlessly under mild conditions using low catalyst loading and affords remarkable selectivity towards alkylated or alkenylated products with high level of functional
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.