Scholars Central

Conference abstractPublished 24 Sep 2018

P-type Cu2O-based heterojunction solar cells fabricated with n-type ZnO thin film prepared by electrochemical deposition method

Authors: Toshihiro Miyata, Hiroki Tokunaga, Tadatsugu Minami

Ask about this article

Abstract

Select any words in the title or abstract, or press this and choose a sentence.

Recently, substantially improved conversion efficiency has been reported in p-type Cu2O sheet-based heterojunction solar cells with n-type oxide semiconductor thin films prepared by the pulsed laser deposition (PLD) method. However, PLD has some disadvantages as a practical preparation method, such as low deposition rate, small deposition area and high cost. On the other hand, the electrochemical deposition (ECD) method is a deposition technique that has potential to solve these problems. This paper describes the fabrication of Cu2O based heterojunction solar cells using n-type ZnO thin film prepared by the ECD method. The n-type ZnO thin film layer was prepared on a p-type Cu2O: Na sheet using the following ECD process. Initially, a zinc nitrate aqueous solution was prepared with 0.22 M zinc nitrate and de-ionized water; after that, a 0.3 M HCl or 0.1 M KOH aqueous solution was added to adjust the pH. Next, a p-Cu2O: Na sheet was immersed in the above solution. The photovoltaic properties were strongly dependent on the fabrication conditions of n-type ZnO thin films. For example; the current density-voltage (J-V) characteristics of AZO/n-ZnO/p-Cu2O: Na solar cells showed strong dependence on the pH of the zinc acetate aqueous solution, obtaining significant improvement with a pH value of 4.9 in Figure 1. Figure 2 shows typical J-V characteristics for AZO/n-ZnO/p-Cu2O solar cells prepared under optimized deposition conditions, such as film thickness of the n-ZnO thin film. The same structure of a Cu2O heterojunction solar cell using n-type ZnO thin films was prepared by PLD, and the J-V characteristics are also shown in Figure 2. It should be noted that the J-V characteristics of the AZO/n- ZnO/p-Cu2O solar cells were the same as those when using the PLD method. Recent Publications 1. T Minami, J Yamazaki and T Miyata (2016) Efficiency enhanced solar cells with a Cu2O homojunction grown epitaxially on p-Cu2O: Na sheets by electrochemical deposition. MRS Communications 6:416-420. 2. Y Nishi, T Miyata and T Minami (2016) Electrochemically deposited Cu2O thin films on thermally oxidized Cu2O sheets for solar cell applications. Solar Energy Materials and Solar Cells 155:405-410. 3. T Minami, T Miyata and Y Nishi (2016) Relationship between the electrical properties of the n-oxide and p-Cu2O layers and the photovoltaic properties of Cu2O-based heterojunction solar cells. Solar Energy Materials and Solar Cells 147:85- 93. 4. T Minami, T Miyata and Y Nishi (2014) Cu2O-based heterojunction solar cells with an Al-doped ZnO/oxide semiconductor/thermally oxidized Cu2O sheet structure. Solar Energy 105:206-217. 5. T Minami, T Miyata and Y Nishi (2014) Efficiency improvement of Cu2O-based heterojunction solar cells fabricated using thermally oxidized copper sheets. Thin Solid Films 559:105-111.

Ask about this article

Answers come only from this article's title, abstract and keywords, each sentence pointing to where it comes from. Your question is sent to OpenAI to write the answer. Scholars Central does not store it.

Try:

More from this journal

The newest in Research & Reviews: Journal of Material Sciences.

All its articles

Conferences in this field

Upcoming conferences in this field.

Follow

New articles from what you follow go into your email digest, once you agree to alert emails.

  • JournalResearch & Reviews: Journal of Material Sciences
  • SubjectMaterials Science
  • BylineArticles whose byline prints “Toshihiro Miyata”
  • BylineArticles whose byline prints “Hiroki Tokunaga”
  • BylineArticles whose byline prints “Tadatsugu Minami”