subjected to a micro-shear test. Atomic force microscopy used to evaluate the surface roughness. Data were analyzed by 2-Way Anova and Tukey test (? = 5%). Result: Sandblasted (SB) demonstrated ... strength for Celtra…
samples was performed using AFM. Statistical analysis: Root mean square (RMS) and surface roughness parameters were used to compare the structure of GP points with contact mode imaging. These values ... were considered…
surface morphology. Effect of oxidation temperature on thin films properties was also investigated. The surface roughness of deposited Bi2O3 thin films were found to increase on glass while it reduced ... films showed…
items and studies need to be carried out, expecially the high level of the surface roughness. In according to the industrial needs in this work it have been studied ... chemical finishing in order to improve the surface…
items and studies need to be carried out, expecially the high level of the surface roughness. In according to the industrial needs in this work it have been studied ... chemical finishing in order to improve the surface…
extensive discussions with practicing engineers in regional extrusion plants, and extrusion research conducted over roughly two decades. Introduction: Aluminum extrusion is primarily a hot working process with high…
crosshead speed of 0.5 mm/minute. In addition, the correlation between the surface roughness and bond strength was checked using Spearman correlation test (The mean difference is significant ... lowest with the control…
process performance is measured in terms of Response variables like Material Removal Rate(MRR) & Surface Roughness(SR). Number of experiments to be conducted is based on Taguchi orthogonal array with ... three factors…
available composites (microhybrid, nanohybrid, and bulk-fill) were tested for flexural strength, hardness, and surface roughness pre- and post-cyclic loading. Nanohybrid composites demonstrated superior retention of…
with (2% chlorhexidine) and decreased with (0.25% NAOCL), (NAOCL 0.5%) respectively. The results of surface roughness showed slightly increased values in (2% chlorhexidine) when compared to control group while increase…
densely twined together as agglomerated particles. The increasing P12FMA content could obviously increase the surface roughness of the film (50-500 nm) and thereby contributes to the hydrophobic ... ether methacrylate…
solution of copper (II) chloride, metallic copper films have been electrochemically deposited onto the rough surfaces of porous silicon. Employing the scanning electron microscopy, we have characterized the surface…
oxidation. To evaluate the change in surface topography and surface free energy after treatment, surface roughness and contact angle measurements were performed. Biological analysis with MC3T3-E1 cells was carried…
investigate the effect of immersion in different disinfectant solutions, on hardness and surface roughness of a heat-cured acrylic resin. Materials and Methods: Specimens were immersed in distilled water, commercial…
features, multiscale features. This research outlines critical background information to understand the importance of surface topography features on osseointegration. It also details experimental findings on the etching…
process. This paper assesses the influence of process parameters on depth of cut and surface roughness which are the important cutting performance measures in abrasive waterjet cutting of materials. Experiments…
wires released almost the same amount of Ni ions. After clinical exposure more surface roughness was recorded for superelastic NiTi wires and heat activated NiTi wires. However, retrieved superelastic NiTi ... Both…
wires released almost the same amount of Ni ions. After clinical exposure more surface roughness was recorded for superelastic NiTi wires and heat activated NiTi wires. However, retrieved superelastic NiTi ... Both…
friction wear test were employed to evaluate corrosion and abrasion resistance, as well as surface roughness and hardness of the coatings. The in-depth investigation was also focused
This report presents an experimental investigation on the change of output parameters especially surface roughness during machining aluminum alloy 6063 using minimum quantity lubricant (MQL) technique. The minimum…
wires released almost the same amount of Ni ions. After clinical exposure more surface roughness was recorded for super-elastic NiTi wires and heatactivated NiTi wires. However, retrieved super-elastic ... Conclusions…
500μm via SEM observation. Titanium powders melted into round convex particles and formed a rough surface for the implants. The normal differentiation on the implant was present in the human ... time. Conclusions: Our…
treatment was then carried out to optimize the concentration of nano particles and their surface roughness and arrangement was studied using AFM and Raman spectroscopy. It was found that nano ... Detailed analysis using…
then they were washed with distilled water for five minutes. Next microhardness testing and surface roughness testing were applied to all speciments. The data were evaluated using SPSS 15.0 software ... statistically…
microcracks formation and to estimate the dependences of the Poisson's ratio and the surface roughness on the degree of uniaxial tension. Recent Publications 1. Dorozhkin V.P., Muradyan V.E., Mokhnatkin ... Microscopy…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.