This paper presents the investigation on material removal rate (MRR) and tool wear rate (TWR) of high speed steel with copper and brass electrode for Electrical Discharge machining (EDM) process
PECM parameters such as voltage, feed rate, and pulse on time, duty cycle on MRR. Keeping pressure constant, Taguchi‟s orthogonal array L9 has been effectively used to study ... effect of independent process parameters…
Pulse on time, Pulse off time, Peak current, Wire feed) on Material Removal Rate (MRR) and Surface Roughness of AA7075/ TiB2 (3wt%) Metal Matrix Composite were optimized. Taguchi’s Signal
conducted to determine the main machining parameters which contribute to material removal rate (MRR) and surface roughness (SR) in wire-EDM of mild steel. In WEDM operations, Proper selection ... process parameters is…
speed, feed rate and depth of cut on surface roughness and material removal rate (MRR) in a turning operation are investigated by using the Taguchi optimization method. A three level ... radius were the most influential…
precision and productivity, the control of surface roughness (Ra) together with Material Removal Rate (MRR) have become more significant. This paper optimizes the process parameters (spindle speed, feed and depth…
because improvement of more than one machining performance measures viz. material removal rate (MRR), surface finish (SF) are sought to obtain precision in work. An attempt to determine parameters setting ... measure is…
combination with the possibilities they offer for integration in optofluidic devices. The microring resonator (MRR), for example, is a very feasible structure to be used as microarray sensor element ... index…
process performance is measured in terms of Response variables like Material Removal Rate(MRR) & Surface Roughness(SR). Number of experiments to be conducted is based on Taguchi orthogonal array with ... three level and…
time, wire tension and dielectric flow rate are investigated for material removal rate (MRR) and surface roughness (SR) during intricate machining of a carbide block. In order to optimize MRR
input parameters of a neural network to identify the sensitivity among machining operations, MRR and surface roughness. The experimental data is later used to predictoutput data by using artificial neural ... Neural…
pulse interval (TOFF), applied voltage (V), air pressure (P) on the material removal rate (MRR) and surface roughness (Ra) have been analyzed using central composite design method ... experiments. The mathematical…
calculated for the machining at the corresponding power. The material removal rate (MRR) is computed. Surface roughness value is measured on the machined surface. The machining parameters at different power…
comparing the ranking of the correct diagnosis by each system using Mean Reciprocal Rank (MRR) and Recall at Rank for ranks 1, 5, 10, 20, 30 and 40. ChatGPT4 ... provide a complete reference citation for each diagnosis…
parameters such as surface finish was found to be 43.17% and material removal rate (MRR) of 9.5% has been obtained after performing ANOM studies. The results has been validated
this study, to optimize three machining outputs, namely surface finish, material removal rate (MRR) and power consumption for 3 input parameters, namely cutting speed, feed rate and depth ... where the Taguchi L9…
assisted polishing (S-EOAP) can be realized, which can obtain high material removal rate (MRR) and smooth surface quality at the same time. The S-EOAP experiments were conducted
process performance is measured in terms of Response variables like Material Removal Rate(MRR),Surface Finish(SF) / Surface Roughness(SR),Tool Wear Rate(TWR)/Electrode Wear Rate(EWR),etc. Various
process performance is measured in terms of Response variables like Material Removal Rate(MRR),Surface Finish(SF) / Surface Roughness(SR),Tool Wear Rate(TWR)/Electrode Wear Rate(EWR),etc. Various
study the effect of speed, feed and depth of cut on Material Removal Rate(MRR) and cutting force (F c) in turning mild steel using high speed steel cutting tool
electrolyte concentration and varied within the selected range to study the metal removal rate (MRR) of ECM of LM6 Al-B4C metal matrix composites produced through stir casting process. Mathematical ... model for MRR was…
Nigeria. Economic evaluation was carried out using partial budget and Marginal Rate of Return (MRR) Analyses. The result showed that higher net returns were obtained from inorganic fertilizer ... N274,826 in 1995 and…
artificial neural network model for two of the important output characteristics; material removal rate (MRR) and surface roughness (Ra). The models have found to be very accurate to predict ... output characteristics…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.