operation of MSC Co., the mentioned steel with the following specification yield point: 80-120, UTS: 200-300MP and elongation 50 % was produced and its behavior was analyzed
over the past three decades or so. Employment of infill plates made of low yield point (LYP) steel with considerably low yield stress and high elongation capacity is believed
abbreviation. Proving the theory of the use of low-yield-point steel in lateral load resisting systems, several experiments were conducted around the world among which the most important ... paper. In this paper, three…
operation of MSC Co., the mentioned steel with the following specification yield point: 80-120, UTS: 200- 300 MP and elongation 50% was produced and its behavior was analyzed
compared to a reference fluid. The average range of apparent viscosity, plastic viscosity, yield point, and low-shear-rate yield point for the prepared drilling muds
force-resisting system in design and retrofit of buildings. Development and use of low yield point (LYP) steel with considerably low yield stress and high elongation capacity nowadays provides
results were displayed in order to choose the optimum scaling function (OSF) at a yielding point, for the seismic signal to preserve the signal signatures
twins in the as forged samples. The dislocations were significantly increased at the yielding point and predominantly distributed around the grain boundaries. These increased dislocations strongly impeded the motion
improves rheological properties of the WBM, such as increases the quantity of plastic viscosity, yield point, and water loss of the sample and increases the shale recovery. In the presence ... Polyethylene Glycol (PEG)…
precipitates, which are arranged in fine lines [1, 4]. Consequently, the toughness, yield point and ultimate tensile strength, formability, and weldability of the micro alloyed steel are increased with small ... micro…
objective of this study was to determine effects of watering points on canopy cover, botanical composition, and hay yields of pastures using transect method. Data were collected from 4 different ... percentage of…
value, saponification value and unsaponifiable matter, while the physical properties include moisture content, yield, melting point, relative density, and refractive index. The data collected were analyzed statistically…
performed on the No-Twist mill process in the rod rolling. Some notable points such as the geometry extraction of rolling line of end product, rod velocity during rolling, neutral ... experiment are performed. It can be…
operations. Therefore, the impact of mud weight in the prediction of plastic viscosity, yield point or apparent viscosity is minimal. The model in this work was obtained for a specific
this paper, different experiments related to mud weight, viscosity, gel strength, filtration and yield point were examined to determine the rheology of multiple mud samples, and data were collected
microns and 300 microns), the filtration, density, specific gravity, pH, plastic viscosity, apparent viscosity, yield point, 10-s gel strength and 10-mins gel strength value fall within the range
result from the intrinsic material's capacity to undergo local lattice transformations beyond tensile yield points as well as from relatively simple activation of lattice slip, according to ab initio
that HIPOLY based drilling fluid show promising results. The Rheological properties like Plastic viscosity, yield point and gel strength remained effective even at high temperature. Likewise, fluid loss was also
which will result in change of the drilling fluid properties such as plastic viscosity, yield point and gel strength before and after hot rolled. The properties are studied using equipment
that of Mucuna solannie is slightly better than the existing muds in terms of yield point, gel strength and emulsion stability. The results of cement slurry measurements also portrayed
Viscosimeter FANN35®. The measured parameters were apparent and plastic viscosity (AV, PV) and yield point (YP). Findings: There is a high content of pure palygorskite in the samples but high
respectively. Stress Vs strain curves revealed that the normalized samples showed a yield point phenomenon while the hardened samples did not. The microstructure of the normalized sample is constituted
applying uniaxial loading and increased with increasing biaxial tensile ones. Both elastic modulus and yield points in uniaxial and biaxial mode of stress were obtained and compared with increasing
parameters (e.g. ROP, SPM, RPM, WOB, bit type) and mud properties (e.g. mud weight, yield point, gel strength) at the time of each event were recorded along with the lost
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.