fabrication of MMNCs is quite a challenge, which includes processing techniques like Spark Plasma Sintering (SPS), etc. The objective of the present work is to fabricate aluminium based MMNCs with ... addition of small…
Sintering techniques play a pivotal role in modern manufacturing, enhancing the properties of powdered materials through controlled heating and densification processes. This case study explores recent advancements in…
grain size of 20 nm. The obtained nanopowders were then consolidated by spark plasma sintering (SPS) for 5 min at 1800 °C and under a pressure of 80 MPa. Microstructural ... samples can reach over 98 % and the Vickers…
alloys fabricated from conventional techniques, not much work involving the uses of spark plasma sintering is available. In this study, Ti-30Ta and Ti-30Zr based alloys have been fabricated ... from elemental powders…
multiscale multiphysics MARMOT models. In this talk, recent advancements of using field-assisted sintering technologies, specifically spark plasma sintering (SPS), in fabricating advanced fuels and engineering fuel…
Polycrystalline PbTiO3 ceramics were fabricated through solid state sintering reaction method at Pb/Ti molar ratio of x=1.00, 0.98 and 0.94. Keeping the technological position of PbTiO3 ceramics ... variety of…
carbide (TiC) ultra high temperature ceramic with 3.5 wt.% of tungsten carbide (WC) as sintering aid was fabricated using spark plasma sintering (SPS) technique at 1600Ã ... pressure. In-situ formation of wide graphene…
parametric studies have been conducted to assess the impact of prominent paramters of sintering process on perforamcne of magentic abrasives. The sintering time, concentration of abrasive and ferromagetic powder…
barium titanate powder by solid state, fabricate the barium titanate granulate material and finally sintered material in order to verify if this material can be successful utilised for manufacturing ... values of water…
volume fractions (0.3, 0.6, 0.9 and 1.2 vol.%) of Si3N4 were fabricated using microwave sintering process. The Powders of Al and Si3N4 with exact stoichiometry ratios were intimately mixed through ... temperature (450…
cubic Boron Nitride (cBN) reinforced alpha-Sialon nano-composites were prepared using Spark Plasma Sintering (SPS) technique. The starting powders including Sialon precursors and various particles size ... were…
Sintering temperature and time have an effect on the densification and distortion of liquid phase sintered tungsten heavy alloys. Quenching was used to observe the in situ microstructure at different ... micro…
demonstrated that the compounds weremutuallymiscible in the solid solution. The dielectric constant in different sintering temperature was discussed. The result showed that the sample reached a high dielectric constant…
powder, are mainly applied in high-temperature 3D printing. The techniques including Selective Laser Sintering(SLS), Selective Laser Melting(SLM). NdFeB is the organic-based composites The purpose of this ... paper is…
describes the production and characterisation of net-shaped bonded NdFeB magnets using selective laser sintering (SLS) from mechanically mixed powders. Net-shaped magnets, cuboids for geometrical measurements and…
ceramics were prepared by sol-gel route. The prepared samples were sintered by using microwave sintering. The phase composition and microstructure were studied by means of X-ray diffraction
effect of polymeric binders and internal lubricant on mechanical properties and microstructure of sintered alumina. Three different formulations of alumina-binders were used which contained 3 wt% of Polyethylene Glycol…
Fe80Al20Si20 (wt. %) alloys were prepared by mechanical alloying (MA) and compacted by spark plasma sintering (SPS) technique. The influence of either the conditions of MA and consequential compaction
addressed by using a unique combination of mechanical alloying and Spark Plasma Sintering (SPS) techniques via powder metallurgy route. Rhenium was added to lower ductile-to-brittle transition temperature ... green…
This investigation represents the notable influence of sintering time on the crystal phase development of copper ferrite nanoparticles synthesized using sol-gel auto-combustion method. Characterization of sintered…
promising as a potential material for biomedical applications. This paper describes the effect of sintering conditions on microstructural, mechanical, and electrochemical properties of injection molded for Co-based…
weight, its high hardness and its high capacity to absorb neutrons. The poor sinterability inherent to the covalent character of the B-C bonding makes the complete densification of boron ... carbide powder difficult to…
weight, its high hardness and its high capacity to absorb neutrons. The poor sinterability inherent to the covalent character of the B-C bonding makes the complete densification of boron ... carbide powder difficult to…
powder mixing and the bond coat was synthesized through the application of spark plasma sintering (SPS) at 1100°C, 1050°C and 1100°C to produce a fully dense ... Ni22Cr11Al bulk samples. The influence of sintering…
devices, a high density solid material is needed, instead of a nanoparticle powder. Classic sintering processes, however, lead to a rapid grain growth and hence to the loss of magnetic ... properties associated with the…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.