including cutting speed, feed rate and depth of cut on surface roughness and material removal rate (MRR) in a turning operation are investigated by using the Taguchi optimization method ... nose radius were the most…
time, pulse-off time, wire tension and dielectric flow rate are investigated for material removal rate (MRR) and surface roughness (SR) during intricate machining of a carbide block. In order
this study is to propose an optimal regression model to analyze the material removal rate in ultrasonic machining through the experimental tests, statistical analyses and regression modeling. Three main factors
This paper deals with Electrochemical machining method to find the material removal rate, surface roughness and overcut by electrochemical dissolution of an anodically polarized work piece (AISI304 s tainless steel…
treatment on NiTi workpiece and copper electrode is investigated. EDM performance measures viz. Material removal rate and tool wear rate are evaluated against the variation of gap current, pulse ... tool. It is…
experimental investigation was conducted to determine the main machining parameters which contribute to material removal rate (MRR) and surface roughness (SR) in wire-EDM of mild steel. In WEDM operations ... maximum…
Speed, Feed Rate, and Depth of cut on the Power, Surface Roughness, and Material Removal Rate are analyzed using Grey relational analysis on a CNC turning machine. Analysis of variance
Statistical analysis: In this study, to optimize three machining outputs, namely surface finish, material removal rate (MRR) and power consumption for 3 input parameters, namely cutting speed, feed rate
concludes that hard abrasive gives the large stressed zone, which increases the material removal rate. In this experimental study, Boron carbide abrasive gives better material removal rate as compared ... Silicon…
This paper presents the investigation on material removal rate (MRR) and tool wear rate (TWR) of high speed steel with copper and brass electrode for Electrical Discharge machining (EDM) process ... optimal parameters…
challenging one because improvement of more than one machining performance measures viz. material removal rate (MRR), surface finish (SF) are sought to obtain precision in work. An attempt to determine ... determine the…
characterized by top kerf width, bottom kerf width, heat affected zone, dross and material removal rate. In the current work attempts are made to minimize the top kerf width, bottom ... kerf width and maximize the…
constant. And the product quality in terms of Surface roughness and productivity as material removal rate is measured. An orthogonal array of L3 was used and ANAOVA were performed ... significance of each of the input…
combinations of electrolytes, sodium chloride and sodium nitrate, with individual concentrations providing maximum machining rates. Conductivity was measured for each sample and recorded. Standard conductivity versus…
past years many researchers have done various advancements in material removal rate, wear of electrode is improved and various researches had done on physical and electrical parameters of EDM machine ... This new…
such as poor surface finish, unacceptable accuracy, excess noise, tool wear and lower Material Removal Rate (MRR). Chatter is self-excited vibration which can occur by various phenomenon’s like ... optimal selection of…
study the effect of speed, feed and depth of cut on Material Removal Rate(MRR) and cutting force (F c) in turning mild steel using high speed steel cutting tool ... speed, feed, and depth of cut significantly influenced…
process. This study is focused on evaluation of ECD process by comparison of material removal rates and maximum current obtained by variation in process parameters like machining time, electrolyte concentration
components. Hence, it is important to optimize its process parameters to obtain high material removal rates and cost efficiencies. The domain of this paper focuses on the electrolyte types
Machining (EDM) process to identify the variations in three performance characteristics such as rate of material removal, wear rate on tool, and surface roughness value on the work material ... machining parameters for…
aluminum oxide (Al2O3) as abrasive powder. The effect of Overcut (OC) and Material removal rate (MRR) of glass material was finding by using L9 orthogonal array based on Taguchi design
finishing process characterized by excellent process capabilities in terms of surface finish and material removal rate. It has wide applications in manufacturing industry as it can handle a wide variety
particulate on the based material Al6061, the surface roughness (SR) and Material removal rate (MRR) values were investigated through L27 orthogonal array
cutting parameters ,those are a cutting speed of 1000, 1500, 2000m/min, feed rate of 0.025, 0.05, 0.075mm/rev, and cutting depth0.5, 0.75, 1mm. An attempt has been made ... surface roughness using Taguchi technique…
For authors and organisers
Publish, present and keep up with your field
Find the right journal for your paper and submit your manuscript.